Fluke 717 1000G Instruction Sheet Download Page 16

English  

Safety Compliance: 

IEC 61010-1 2nd Edition CAT I, 30 V;

 

Pollution Degree 2 

CSA C22.2 No. 1010.1; 
ANSI/ISA S82.02. Maximum Transient Overvoltage: 240 VAC for 10 
Seconds. 

CE: 

Complies with EN 61326 Class A; EN61010-1 

Protection Class: Class II, Double Insulated 
Power requirements:  

Single 9 V battery (ANSI/NEDA 1604A or IEC 6LR61) 

Size:  

34.9 mm H x 87 mm W x 187 mm L 
(1.55 in H x 3.41 in W x 7.35 in L); 
With holster and Flex-Stand: 52 mm H x 98 mm W x 201 mm L (2.06 in H x 
3.86 in W x 7.93 in L) 

Weight:  

369 g (13 oz);  
With holster and Flex-Stand: 624 g (22 oz) 

Contacting Fluke 

To contact Fluke for product information, operating assistance, service, or to get 
the location of the nearest Fluke distributor or service center, call: 

USA:  1-888-99-FLUKE (1-888-993-5853) 
Canada:  1-800-36-FLUKE (1-800-363-5853) 
Europe:  +31 402-675-200 
Japan:  +81-3-3434-0181 
Singapore:  +65-738-5655 
Anywhere in the world:  +1-425-446-5500 

Or visit Fluke's web site at: 

www.fluke.com

.  

Register your Calibrator at: 

http://register.fluke.com

.  

Address correspondence to: 

Fluke Corporation 

Fluke Europe B.V. 

P.O. Box 9090, 

P.O. Box 1186, 

Everett, WA 98206-9090 

5602 BD Eindhoven 

U.S.A. The 

Netherlands 

 

Limited Warranty & Limitation Of Liability 

This Fluke product will be free from defects in material and workmanship for 3 years from 
the date of purchase. This warranty does not cover fuses, disposable batteries, or damage 
from accident, neglect, misuse, alteration, contamination, or abnormal conditions of 
operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s 
behalf. To obtain service during the warranty period, contact your nearest Fluke authorized 
service center to obtain return authorization information, then send the product to that 
Service Center with a description of the problem. 
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS 
FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE 
FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, 
ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the 
exclusion or limitation of an implied warranty or of incidental or consequential damages, 
this limitation of liability may not apply to you. 

11/99 

 

Shop for Fluke products online at:

1.888.610.7664

www.

MyFlukeStore

.com

Summary of Contents for 717 1000G

















Reviews: