background image

28 II Ex 

Calibration Information 

8

 

Frequency Counter Sensitivity and Trigger Levels 

Input Range 

Minimum Sensitivity (RMS Sine Wave) 

Approximate Trigger Level 

(DC Voltage Function) 

5 Hz – 20 kHz 

0.5 Hz – 200 kHz 

600 mV dc 

70 mV (to 400 Hz) 

70 mV (to 400 Hz) 

40 mV 

600 mV ac 

150 mV 

150 mV 

6 V 

0.3 V 

0.7 V 

1.7 V 

60 V 

3 V 

7 V (

140 kHz) 

4 V 

600 V 

30 V 

70 V (

14.0 kHz) 

40 V 

1000 V 

100 V 

200 V (

1.4 kHz) 

100 V 

Duty Cycle (Vdc and mVdc) 

Range Accuracy 

0.0 % to 99.9 %

 [1]

 

Within 

±

 (0.2 % per kHz + 0.1 %) for rise times <1 

μ

s. 

[1]  0.5 Hz to 200 kHz, pulse width >2 

μ

s. Pulse width range is determined by the frequency by the frequency of the signal. 

Input Characteristics 

Function 

Overload 

Protection 

Input 

Impedance 

(nominal) 

Common Mode  
Rejection Ratio  

(1 k

Ω

 unbalance) 

Normal Mode Rejection 

L

 

1000 V rms 

10 M

Ω

 <100 pF 

> 120 dB at dc, 50 Hz 

or 60 Hz 

> 60 dB at 50 Hz or 60 Hz 

 

1000 V rms 

> 120 dB at dc, 50 Hz 

or 60 Hz 

> 60 dB at 50 Hz or 60 Hz 

K

 

1000 V rms  10 M

Ω

 < 100 pF 

(ac-coupled) 

> 60 dB, dc to 60 Hz 

 

 

 

Open Circuit 
Test Voltage 

Full Scale Voltage 

Typical Short Circuit Current 

 

 

To 6 M

Ω

 

5 M

Ω

 or 

60 nS 

600 

Ω

6 k

Ω

 60 

k

Ω

 600 

k

Ω

 6 

M

Ω

50 M

Ω

Ω

 

1000 V rms 

<7.0 V dc 

<1.7 V dc 

<1.9 V dc  500 

μ

A 100 

μ

A 10 

μ

A 1 

μ

A 0.4 

μ

A 0.2 

μ

A

G

 

1000 V rms 

<7.0 V dc 

2.200 V dc 

1.0 mA typical 

MIN MAX Recording 

Nominal Response 

Accuracy 

100 ms to 80 % 
(dc functions) 

Specified accuracy 

±

12 counts for changes >200 ms in duration 

120 ms to 80 % 
(ac functions) 

Specified accuracy 

±

40 counts for changes >350 ms and inputs >25 % of range 

250 

μ

s (peak)

 [1]

 

Specified accuracy 

±

100 counts for changes >250 

μ

s in duration 

(add 

±

100 counts for readings over 6000 counts)  

(add 

±

100 counts for readings in Low Pass mode) 

 [1]  For 6 V range: 1 ms 

Summary of Contents for 28 II Ex





















Reviews: