background image

LACO USER MANUAL - GASCHECK G SERIES

9

© 2018 FLUIDX Equipment, Inc.

3.8 

FUNCTIONS

The GasCheck instruments have a variation of functionality. Each of the 
functions listed below has a number to the right of the heading. This 
number indicates which function is included with each model.

Table 6: GasCheck Function Comparison

FUNCTION

DESCRIPTION

MODEL

CONTRAST

Use this function to adjust the contrast of the GasCheck LCD (liquid crystal display). 

Significant variations in ambient temperature conditions can cause the display to 

appear too dark or too light.
When this function is selected, a number will appear to the right of the Contrast 

symbol as a percentage. Use the UP and DOWN keys to adjust the display the contrast 

to the desired level. When satisfied with the contrast level, press the ESC key to exit to 

the MAIN MENU.

G1, G2, G3

BACKLIGHT

The user can select either BACKLIGHT ON or BACKLIGHT OFF. In daylight, the user may 

not be able to determine if the backlight is ON or OFF. A symbol on the main RUNNING 

SCREEN shows the status.
When the backlight is ON, it significantly reduces battery life. 

Backlight Off=40 hours of use 

Backlight On=20 hours of use

G1, G2, G3

SOUND

The GasCheck has an audible sounder that increases frequency as detected gas levels 

increase. This sounder can be switched ON and OFF. Use the UP or DOWN key to move 

the “tick” to the desired position and then press the ESC key to return to the MAIN 

MENU.
An audible beep can also be heard whenever the key pad is  

pressed. This beep cannot be switched off.

G1, G2, G3

PEAK HOLD

When selected, this function holds the highest detected  

reading on the display until the ENTER key is pressed.
Select Peak ON or OFF using the UP or DOWN key and then  

press the ESC key to exit to the MAIN MENU.
When using the GasCheck G, press the ENTER key to clear the held reading. The 

reading held on screen will be logged when the ENTER key is pressed. 
WARNING: ZEROing the instrument in a contaminated environment will result in false 

readings.

G2, G3

CALIBRATION

There are two Calibration settings that can be selected:  

FACTORY and CUSTOM. Factory calibration is carried out shortly  

after manufacture and cannot be adjusted. However, custom  

calibration offers the ability to calibrate the instrument between  

annual Factory calibrations. The GasCheck G ZEROs its reading  

at switch ON. Therefore, the Custom calibration routine has only  

one stage. For more information, see 5.1 CALIBRATION..

BATTERY  

SELECTION

The GasCheck will operate using AA size batteries in either  

Alkaline (non rechargeable) or Nickel Metal Hydride  

(rechargeable).
Select the battery type using the UP or DOWN key and then  

ress the ESC key to exit to the MAIN MENU.
Failing to select the correct battery type will not damage the instrument or affect its 

ability to detect gas. However, it will cause the battery indicator to read incorrectly.

Summary of Contents for GasCheck G Series






















Reviews: