manualshive.com logo in svg

Fluidwell F126-P-EG-TP, Manual

Share
Download
Fluidwell F126-P-EG-TP Manual Download Page 25

 

FW_F126PEGTP_v1901_04_EN.docx 

Page 25 

4.4.6. 

TERMINAL CONNECTORS 

Refer to Appendix A: Technical Specification 
 

 

For Intrinsically safe applications: read chapter 5. 

 

Fig. 8: Overview of terminal connectors - Standard configuration and options 

 
4.4.7. 

VOLTAGE SELECTION SENSOR SUPPLY 

For type PB/PC; PX; AP:

 There is no real sensor supply out available. Only a limited power supply 

is available. This power supply MAY NOT be used to supply the flowmeters electronics, converters 
etc. as it will not provide adequate sustained power ! All energy used by the flowmeters pick-up will 
directly influence the battery life-time. It is strongly advised to use a "zero power" pickup such as a 
coil or reed-switch when operating without external power. It is possible to use some low power NPN 
or PNP output signals, but the battery life time will be significantly reduced (consult your distributor). 
The sensor supply is fixed: 1.2V DC or 3V DC (set by the firmware). 

For type PD; PF; PM:

 It is possible to supply the sensor with different voltages. You can set the 

voltage with the switches. Internal power is only applicable for low power sensors (Coil, Reed). 
External power is only available when the main external power supply is connected.  
The sensor supply voltage is selectable: 1.2; 3; 8.2; 12 or 24V DC. 

Summary of Contents for F126-P-EG-TP





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands