background image

2

 

 

 
 
 
 

 

 1. PREFACE 

 

This  appliance  can  be  used    by    children    aged    from    8  years    and    above    and    persons 
with  reduced  physical,  sensory  or  mental  capabilities  or    lack    of    experience    and 
knowledge  if  they  have  been  given  supervision  or  instruction  concerning  use  of  the 
appliance  in  a  safe  way  and  understand  the  hazards  involved.  Children  shall  not  play  with 
the  appliance.  Cleaning  and  user  maintenance  shall  not  be  made  by  children  without 
supervision.

 

 

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly 

qualified persons in order to avoid a hazard.

 

 

The appliance shall be installed in accordance with national wiring regulations.

 

 

Do not operate your air conditioner in a wet room such as a bathroom or laundry room.

 

 

Before obtaining access to terminals, all supply circuits must be disconnected.

 

 

An all-pole disconnection device which has at least 3mm clearances in all pole

 

have a  leakage current that may exceed  10mA 

residual  current  device  (RCD)  having 

a   rated  residual  operating  current   not exceeding   30mA 

disconnection  must  be 

incorporated in the fixed wiring in accordance with the wiring rules

 

Do not use means to accelerate the defrosting process or to clean, other than those recommended 
by the manufacturer

 

The appliance shall be stored in a room without continuously operating ignition sources (for example: 
open flames, an operating gas appliance or an operating electric heater.)

 

 

Do not pierce or burn

 

Appliance shall be installed, operated and stored in a room with a floor area larger than 30 m2 Be 

aware that refrigerants may not contain an odour.

 

The installation of pipe-work shall be kept to a minimum 30 m2

 

Spaces where refrigerant pipes shall be compliance with national gas regulations. 
Servicing shall be performed only as recommended by the manufacturer.

 

The appliance shall be stored in a well-ventilated area where the room size corresponds to the room 
area as specified for operation.

 

All working procedure that affets safety means shall only be carried by competent persons.

 

 

Transport of equipment containing flammable refrigerants 
Compliance with the transport regulations

 

Marking of equipment using signs 
Compliance with local regulations

 

Disposal of equipment using flammable refrigerants 
Compliance with national regulations

 

Storage of equipment/appliances

 

The storage of equipment should be in accordance with the manufacturer's instructions. Storage 
of packed (unsold) equipment

 

Storage package protection should be constructed such that mechanical damage to the 
equipment inside the package will not cause a leak of the refrigerant charge.

 

The maximum number of pieces of equipment permitted to be stored together will be 
determined by local regulations.

 

Summary of Contents for 78568





































Reviews: