Flotec FPSE2800A Owner'S Manual Download Page 6

Warranty

6

For parts or assistance, call Flotec Customer Service at 

1-800-365-6832

ATTACH ORIGINAL RECEIPT HERE FOR WARRANTY CONSIDERATION.

FLOTEC warrants to the original consumer purchaser (“Purchaser”) of its products that they are free from defects in
material or workmanship.

If within twelve (12) months from the date of the original consumer purchase any such product shall prove to be defec-
tive, it shall be repaired or replaced at FLOTEC’s option, subject to the terms and conditions set forth below. Your origi-
nal receipt of purchase is required to determine warranty eligibility.

Exceptions to the Twelve (12) Month Warranty

Product

Warranty Period

Drill Pump, Pitcher Pump,

90 days

In-line Water Filter Cartridge

1/3 HP Submersible Sump Pumps
I

NTELLI

P

UMP

(Model FP0S1775A)

2 Years

Back-up Sump Pump System (Model FP2800DCC)

4" Submersible Well Pumps
1/2 HP Submersible Sump Pumps

3 Years

Models FPSC2200A-10 and FPSC2250A-10

Pre-Charge Water System Tank

5 Years

Models FPSC3200A-10 and FPSC3250A-10

Floodmate

®

7000 (Model FP0S6000A)

Ironmate

®

(Model FPSC4550A)

Sewage Ejector (Model FPSE3601A)

Lifetime

Pedestal Sump Pump (Model FPPSS5000)
Utility Pump (Model FPSC1725X)
Submersible Sump Pump (Model FPSC4550A-10)

General Terms and Conditions

Purchaser must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty
shall not apply to acts of God, nor shall it apply to products which, in the sole judgement of FLOTEC, have been subject
to negligence, abuse, accident, misapplication, tampering, alteration; nor due to improper installation, operation, mainte-
nance or storage; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system, or operation at pressures in excess of recommended
maximums.

Requests for service under this warranty shall be made by returning the defective product to the Retail outlet or to
FLOTEC as soon as possible after the discovery of any alleged defect. FLOTEC will subsequently take corrective action
as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
30 days after the term of the warranty.

This warranty sets forth FLOTEC’s sole obligation and purchaser’s exclusive remedy for defective products.

FLOTEC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHAT-
SOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESS WARRANTIES PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.

FLOTEC • P.O. Box 342 • Delavan, WI U.S.A. 53115

Phone: 1-800-365-6832 • Fax: 1-800-526-3757

E-Mail: [email protected] • Web Site: http://www.flotecwater.com

Summary of Contents for FPSE2800A

















Reviews: