FITT S.p.A.
Via Piave, 8 - 36066 Sandrigo (VI) Italy
www.fitt.it - info@fitt.it
Stand der Informationen · État des informations · Versione delle informazioni
· Validity of information
Update: 09 /2017
9125379
IAN 291818
1
passed on with the product
• Read all of these safety and operating instructions attentively.
• This product is not a toy.
• Check the garden hose and all fittings supplied with the product for possible damage
before each use.
• Check to ensure that the water tap is closed before the installation of all supplied
connecting pieces onto garden hose.
• After assembly of all of the supplied connection pieces onto the garden hose, and
before the first use of the product, first check that there are no leaks, and only then
open the tap.
• When using the garden hose ensure that no dirt particles can get into it which could
damage or clog the supplied fittings.
• After use, always close the garden hose off at the tap. The garden hose must be
completely emptied. Clean off coarse dirt and keep the garden hose away from direct
sunlight in a protected place, either rolled onto a garden hose cart or by rolling it up
by hand onto a hose holder.
• Do not direct the water jet onto electrical appliances.
• Do not direct the water jet at people or animals.
• Not suitable as a source of drinking water.
• At temperatures below 0°C ensure that the garden hose is emptied completely when
not in use, that the connecting pieces are not mounted on the garden hose, and that
everything is kept protected against frost, as damage could be caused to the product
by freezing water.
GB – Operating Instructions
All of the supplied connecting pieces are for garden hoses with an inner diameter of 13mm
(1/2”) and suitable for taps with a diameter of 26.44mm and a thread of G3/4”.
The assembly and disassembly of the supplied connecting pieces must not be undertaken
by children.
A. Screw the connector for connection to the tap (1) onto a suitable water tap and check
the connection for leaks.
B. Loosen the ring (a) from part (b) of the connecting piece (2), then push it at the narrowest
point onto one end of the garden hose (3). Pull the end of the garden hose (3) to the
stop on part (b) of the connecting piece (2), then firmly screw the ring (a) back onto part
(b) of the connecting piece (2). Check to ensure that the ring (a) is firmly tightened.
C. Repeat the procedure described in section B with connecting piece (4) (Aqua Stop)
at the other end of the garden hose (3). With the help of connecting piece (4) (Aqua-
Stop), the nozzle (5) and any other accessory that has the same quick connector system
of 13mm can be attached. The Aqua-Stop function prevents the escape of water from
connecting piece (4), that is attached to one end of the garden hose as a precautionary
measure, also in the event that the tap has not been closed off during the replacement
of the nozzle (5) for other accessories ,
D. Push the nozzle (5) until it engages (Click!) completely through the connecting piece (4)
(Aqua-Stop), which has been attached onto one end of garden hose as described in
sections B and C. Hereby, hold the nozzle (5) at the knurled part (d) with one hand and
the connecting piece (4) (Aqua-stop) with the other hand, holding it at part (b), which is
equipped round recesses for a safe grip, so as to prevent crushing or abrasion wounds
on fingers or hands when attaching the nozzle.
E. Push the connecting piece (2) until it engages (Click!) completely onto the connecting
piece for the connection to the tap (1), which as described in point A has already been
attached to an appropriate tap. Hereby, hold the connecting piece for connection to
the tap (1) with the fingers of one hand and, with the other hand, the connecting piece
(2), which as described in section B and C has been attached at one end of the garden
hose. To avoid crush or abrasion wounds on the fingers or hands during assembly, hold
the connecting piece (2) at part (b), which is equipped with round recesses for a safe
grip.
F. After completion of the procedures described in sections A, B, C, D and E, take the
nozzle (5) in your hand and open the tap, in that you regulate the water jet depending
on the desired amount of water. You can choose between different types of water jet and
continuously vary the setting from a focused jet of water up to a diffuse spray, in that you
turn part (c) of the nozzle (5) first to the right and then to the left and vice versa. Repeat
this procedure during the first use several times to check that the nozzle (5) also closes
tightly and without leaks.
G. If you wish to exchange the regulatory nozzle for other accessories, which are equipped
for the quick connector system of 13mm, hold the regulatory nozzle (5) with one hand
on the knurled part (d) and the Water-Stop hose connector piece (4) with the other
hand at part (b), which is provided with round recesses for a safe grip and loosen the
regulatory nozzle (5), this is done by pulling part (b) of the Water-Stop hose connector
piece (4) in the direction of the applied arrows. To attach the new accessory, repeat the
procedures described above in section D.
H. If you wish to loosen the connecting piece (2) from the connecting piece for connection
to the tap (1), close the tap, and hold the connecting piece for connection to the tap (1)
with one hand and the connecting piece (2) at part (b), which is provided with round
recesses for a safe grip, with the other hand and pull it in the direction of the applied
arrows.
You receive 3 years warranty with this product.
GB – Service address
FITT S.p.A.
Via Piave, 8 - 36066 Sandrigo (VI) Italy
tel.: +39 0444 461000 - fax: +30 0444 461099
www.fitt.it - info@fitt.it
Issue 01/09/2017
11
10
13
15
14
12
9
16
