background image

920897-02 Rev C 

10/2018

© 2018 Great Plains Industries, Inc., All Rights Reserved.

Great Plains Industries, Inc. / 888-996-3837 /FLOMEC.net

LIMITED WARRANTY

Great Plains Industries, Inc. 5252 E. 36

th

 Street North, Wichita, KS USA 67220-3205, hereby 

provides a limited warranty against defects in material and workmanship on all products 

manufactured by Great Plains Industries, Inc. This product includes a 1 year warranty. 

Manufacturer’s sole obligation under the foregoing warranties will be limited to either, at 

Manufacturer’s option, replacing or repairing defective Goods (subject to limitations hereinaf-

ter provided) or refunding the purchase price for such Goods theretofore paid by the Buyer, 

and Buyer’s exclusive remedy for breach of any such warranties will be enforcement of such 

obligations of Manufacturer. The warranty shall extend to the purchaser of this product and 

to any person to whom such product is transferred during the warranty period.

The warranty period shall begin on the date of manufacture or on the date of  

purchase with an original sales receipt. This warranty shall not apply if:

A. the product has been altered or modified outside  
the warrantor’s duly appointed representative;

B. the product has been subjected to neglect, misuse, abuse or damage or has been in-

stalled or operated other than in accordance with the manufacturer’s operating instructions.

To make a claim against this warranty, contact the GPI Customer Service Department at 

 

316-686-7361 or 888-996-3837. Or by mail at:

Great Plains Industries, Inc.

5252 E. 36

th

 St. North

Wichita, KS, USA 67220-3205

The company shall, notify the customer to either send the product, transportation prepaid, 

to the company at its office in Wichita, Kansas, or to a duly authorized service center. The 

company shall perform all obligations imposed on it by the terms of this  

warranty within 60 days of receipt of the defective product.

GREAT PLAINS INDUSTRIES, INC., EXCLUDES LIABILITY UNDER THIS WARRANTY FOR 

DIRECT, INDIRECT, INCIDENTAL AND CONSEQUENTIAL DAMAGES INCURRED IN THE 

USE OR LOSS OF USE OF THE PRODUCT WARRANTED HEREUNDER.

The company herewith expressly disclaims any warranty of merchantability or fitness for any 

particular purpose other than for which it was designed.

This warranty gives you specific rights and you may also have  

other rights which vary from U.S. state to U.S. state.

Note: In compliance with MAGNUSON MOSS CONSUMER WARRANTY ACT – Part 702 

(governs the resale availability of the warranty terms). 

Summary of Contents for QSI Series





















Reviews: