Flomec 125100-10 Owner'S Manual Download Page 16

 

16 

FLOMEC®  TWO-YEAR  LIMITED  WARRANTY 

Great Plains Industries, Inc. 5252 E. 36th Street North, Wichita, KS USA 67220-3205, hereby 
provides  a  limited  warranty  against  defects  in  material  and  workmanship  on  all  products 
manufactured  by  Great  Plains  Industries,  Inc.  This  product  includes  a  2-year  warranty. 
Manufacturer’s  sole  obligation  under  the  foregoing  warranties  will  be  limited  to  either,  at 
Manufacturer’s  option,  replacing  or  repairing  defective  Goods  (subject  to  limitations 
hereinafter provided) or refunding the purchase price for such Goods theretofore paid by the 
Buyer, and Buyer’s exclusive remedy for breach of any such warranties will be enforcement 
of  such  obligations  of  Manufacturer.  The  warranty  shall  extend  to  the  purchaser  of  this 
product and to any person to whom such product is transferred during the warranty period. 

The warranty period shall begin on the date of manufacture or on the date of purchase with 
an original sales receipt. This warranty shall not apply if: 

A.  the  product  has  been  altered  or  modified  outside  the  warrantor’s  duly  appointed 

representative; 

B.  the product has been subjected to neglect, misuse, abuse or damage or has been 

installed  or  operated  other  than  in  accordance  with  the  manufacturer’s  operating 
instructions. 

To make a claim against this warranty, or for technical assistance or repair, contact your 
FLOMEC distributor or contact FLOMEC at one of the locations below. 
 

In North or South America contact 

 

Great Plains Industries, Inc. 

5252 East 36

th

 St. North  

Wichita, KS  67220-3205 

 USA 

 

888-996-3837 

 

www.flomecmeters.com 

(North America)

 

Outside North or South America contact 

 

GPI Australia 

(Trimec Industries Pty. Ltd.) 

12/7-11 Parraweena Road 

 Caringbah NSW 2229 

Australia 

 

+61 02 9540 4433 

 

www.flomec.com.au

 

The  company  will  step  you  through  a  product  troubleshooting  process  to  determine 
appropriate corrective actions. 

GREAT  PLAINS  INDUSTRIES,  INC.,  EXCLUDES  LIABILITY  UNDER  THIS  WARRANTY 
FOR DIRECT, INDIRECT, INCIDENTAL AND CONSEQUENTIAL DAMAGES INCURRED IN 
THE USE OR LOSS OF USE OF THE PRODUCT WARRANTED HEREUNDER. 

The company herewith expressly disclaims any warranty of merchantability or fitness for any 
particular purpose other than for which it was designed. 

This warranty gives you specific rights and you may also have other rights which vary from 
U.S. state to U.S. state. 

NOTE: In compliance with MAGNUSON MOSS CONSUMER WARRANTY ACT – Part 702 
(governs the resale availability of the warranty terms). 

 
 
 
 

© 2021 Great Plains Industries, Inc., All Rights Reserved. 

Great Plains Industries, Inc. / 888-996-3837 / flomecmeters.com 

 
 
09/2021   

 

 

 

 

 

920907-01 Rev. C 

Summary of Contents for 125100-10

















Reviews: