USER MANUAL
1000W LED
USER MANUAL
1000W LED
2
9
●
Always adhere to local rules and regulations when installing or using the LED fixture.
●
Do not open or disassemble the LED fixture, it contains no serviceable parts inside. Opening or modifying
the LED fixture can be dangerous and will void the warranty.
●
This product may cause interference to radio equipment and should not be installed near maritime safety
communications equipment or other critical navigation or communication equipment operating between
0.45 - 30 MHz.
●
Do not use the LED fixture when either the LED fixture or its power cord are damaged. Replace the power
cord only with original certified cords.
●
Modifications to the cords can lead to unwanted electromagnetic interference and effects and will void
the warranty and nullify any compliance with legal regulations.
●
Do not expose the LED fixture to:
Warning!
Please read the following instructions carefully before using or working with the product!
4.SAFETY RECOMMENDATIONS AND WARNINGS
This product is intended to be used in greenhouses and climate-controlled rooms and can be used in damp
environments. However, please DO NOT use this product outdoors or in wet environments and do not
expose it to water. The LED fixture works at optimal capacity when the ambient air temperature is between
68 ~ 95
° F
/ 20 ~ 35
° C.
3.2 ENVIRONMENT
Warning!
Make sure mains power is switched off before connecting the light fixture.
Caution!
Ensure the cord is not coiled and does not touch any hot surfaces.
Warning!
Connect the cables according to local rules, safety regulations and electrical code.
Warning!
Ensure the external switching gear can cope with the inrush of electric current of the LED fixture (refer
-
ence paragraph 3.1 for further details). Always use a double pole contactor that is suitable for switching a capacitive
load.
●
Connect the M19 female connector on power cable to the male connector on the power supply enclosure.
●
Connect the power cable to the mains.
●
Switch on mains power
Warning!
Do not connect or disconnect the LED fixture under load.
6.6 CONNECTING THE LED FIXTURE TO THE MAINS
Warning!
Always wait 20 - 30 minutes for the LED bars to cool down!
7. PRECAUTIONS WHEN USING THE LED FIXTURE
Warning!
Disconnect the LED fixture from mains before performing any maintenance or repairs.
Warning!
Do not connect or disconnect the LED fixture while it is under load.
Warning!
Do not open or disassemble the LED fixture, it contains no serviceable parts inside. Opening the LED
fixture can be dangerous and will void the warranty.
Warning!
Always allow for a cool down period of at least 30 minutes before touching the LED bars.
Caution!
Do not clean the LED fixture with detergents, abrasives or other aggressive substances.
●
Please regularly check the LED fixture for dust or dirt buildup. Clean if necessary. Contamination may
cause overheating and decreased performance. Clean the outside of the LED fixture using a dry or damp
cloth.
●
Regularly check the cables of the LED fixture to ensure it is undamaged.
8. INSPECTION, MAINTENANCE AND REPAIR
●
Store the LED fixture in a dry and clean environment, with an ambient temperature of -4 ~ 185° F / -20 ~ 85° C.
●
The product must not be discarded as unsorted municipal waste, but must be collected separately for the
purpose of treatment, recovery and environmentally sound disposal.
9. STORAGE AND DISPOSAL
●
Always disconnect the LED fixture from mains before performing any maintenance.
●
Always allow for a cool down period of at least 30 minutes before touching the LED bars. Touching the LED
bars when the fixture is lit or immediately afterwards will result in severe burns!
●
Do not use the LED fixture near flammable, explosive or reactive substances. The LED fixture reaches
temperatures of >104° F / 40° C.
●
Do not use sulfur vaporizers or water misters.
●
The installation and the use of this LED fixture are the responsibility of the end user. Incorrect use or
installation can lead to malfunction and failure of the LED device. Any damage to the LED fixture and
electronic security as a result of incorrect installation and use revokes the warranty.
-- Condensation, humidity, heavy mist, fog, or direct spray;
-- (Ambient) temperatures outside the specified range;
-- Dust and/or contamination;
-- Direct sunlight during use or HID light that could heat up the power supply enclosure.
