background image

 

MD23-190 

 

User Guide 

Mid-Continent Instruments and Avionics 

User Guide UG190, Revision 2 

 

 

January , 2021 

2.1 

CONNECTOR PINOUT 

For standard pre-installation and installation instructions, including location, cable harness 
assembly, pneumatic inputs (if applicable), mounting, and others, please refer to the IM.  

Pinout identification specific to this CID is listed in the table below. A brief description is provided. 
Further definition of the inputs and outputs should be documented in the technical requirements 
and/or statement of work and are not provided within this User Guide. 

 

Connector Pinout 

Pin 

Description 

Function 

Ground 

Power return; connect to a/c ground 

ARINC Out (A) 

ARINC label 150 

ARINC Out (B) 

(paired with pin 2) 

Dimmer Input 

5, 14, or 28VDC input (if used) 

ARINC In 1(A) 

ARINC labels 150, 252 

ARINC In 2(A) 

Reserved 

Reserved 

 

Reserved 

 

Reserved 

 

10 

Reserved 

 

11 

Reserved 

 

12 

Reserved 

 

13 

Reserved 

 

14 

ARINC In 1(B) 

(paired with pin 5) 

15 

Reserved 

 

16 

ARINC In 2(B) 

Reserved 

17 

Reserved 

 

18 

Reserved 

 

19 

Power Input 

+10-32VDC 

20 

Reserved 

 

21 

Reserved 

 

22 

Discrete Input 

Flight Timer Start/Stop Signal 

23 

Discrete Input 

Hobbs Timer Start/Stop Signal 

24 

Reserved 

 

25 

Reserved 

 

26 

Reserved 

 

 

Table 1 Unit Connector Pin Identification 

 

 

 

 

Summary of Contents for MidContinent MD23-190












Reviews: