Flex CS 40 WET Manual Download Page 17

CS 40 WET                                                                            

17

EU  countries  only  Do  not  throw  electric  power  tools  into  the 

household waste!
In  accordance  with  the  European  Directive  2012/19/EC  on  Waste  Electrical 
and  Electronic  Equipment  and  transposition  into  national  law  used  electric 
power tools must be collected separately and recycled in an environmentally 
friendly manner.

  NOTE!

Please ask your dealer about disposal options!

-Declaration of Conformity

We  declare  under  our  sole  responsibility  that  the  product  described  under 
“Technical  specifications”  conforms  to  the  following  standards  or  normative 
documents:

EN 60745 in accordance with the regulations of the directives
2004/108/EC (until 19.04.2016),
2014/30/EU (from 20.04.2016),
2006/42/EC, 2011/65/EC.

Responsible for technical documents:
FLEX-Elektrowerkzeuge  GmbH,  R  &  D  Bahnhofstrasse  15,  D-71711 
Steinheim/Murr

16.10.2015

FLEX-Elektrowerkzeuge GmbH
Bahnhofstrasse 15, D-71711 Steinheim/Murr

Exemption from liability

The  manufacturer  and  his  representative  are  not  liable  for  any  damage  and 
lost  profit  due  to  interruption  in  business  caused  by  the  product  or  by  an 
unusable product.
The manufacturer and his representative are not liable for any damage which 
was caused by improper use of the power tool or by use of the power tool with 
products from other manufacturers.

Summary of Contents for CS 40 WET


















Reviews: