17
FLYING YOUR MAMBA 10 G2
Selecting a Flying Site
Selecting a flying site is critical to a successful flight. Airplanes
require a lot more room than other R/C products, therefore, a
neighborhood or parking lot is less than ideal. A large open field
with short grass and generous overfly area are the best candidates if
no AMA field is available in your area. Know your overfly area -
ensure that there are no houses, playgrounds, or other buildings that
may be damaged if the airplane were to crash.
Takeo
ff
Taxi or place the aircraft on the runway centerline, with the nose into
the wind. Select Flight Mode 1, verify the gyro kill switch is set to the
gyro on position and set the throttle trim so that the motor spins
smoothly at its lowest RPM without stopping. Smoothly advance to
full throttle while maintaining directional control with the rudder
and slight back pressure on the elevator. The airplane should lift o
ff
gently before the throttle is fully open. Fly in Flight Mode 1 until the
aircraft is fully trimmed (see special trimming instructions), and you
are comfortable with its handling, then explore the other modes as
desired.
Flying
Altitude is your friend on the first flight. Briskly climb to a safe
altitude and trim the airplane out. The airplane should fly straight
and level at 1/2 to 3/4 power with no hands on the transmitter. Try
some basic maneuvers, and slowly progress into the airplane’s flight
envelope as you become more comfortable with the airplane’s flight
qualities and perfect your setup. Note: If at any time, such as after
gain adjustments, you experience unexpected control system inputs
or oscillations, use the gyro kill switch (CH7, Aux2) to turn the gyro
o
ff
, land and troubleshoot the issue.
Landing
Be mindful of your flight time and allow adequate battery reserve for
a couple of go-arounds, if necessary, on the first few flights. Select
Flight Mode 1 and slow the airplane and align with the runway, into
the wind. The airplane should descend smoothly in this
configuration with proper airspeed. Once you are close to the
ground, gradually close the throttle fully and begin to smoothly
apply up elevator as required to arrest descent and the airplane
should gently touch down with a short roll out.
Trimming
The first several flights on your new Mamba 10 G2 should be
dedicated to trimming and setup. Fly the airplane at 2/3 power
in any Flight Mode you are comfortable flying in, and trim for
level flight.
DO NOT CHANGE FLIGHT MODES
.
Land, adjust
linkages or execute Quick Trim (see below) and return the
trim and/or sub-trim to zero and fly again. Repeat process
until the airplane flies hands o
ff
, straight and level
.
Transmitter trim or sub-trim will cause trim shifts when
di
ff
erent flight modes are selected. To eliminate this trim shift,
the model should be mechanically trimmed, or Aura “Quick
Trim” may be used instead.
CAUTION
USE CAUTION WHEN FLYING YOUR MAMBA 10 G2 IN MODE 3
AT HIGH AIRSPEEDS. DOING SO CAN INDUCE CONTROL
SURFACE OSCILLATIONS AND MAY CAUSE A CRASH.
Aura Quick Trim
The Aura 8 features a Quick Trim Mode that eliminates the need for
mechanical linkage adjustments during test flights. Aura will learn
the trim values from your transmitter, and apply them to the control
surfaces at power up when enabling quick trim mode.
NOTE: Quick Trim can also be used BEFORE flying to make small
changes to center the control surfaces before flight.
1.
Fly the airplane in your preferred Flight Mode at 2/3 power. Trim
the aircraft with the transmitter trimmers and land.
DO NOT
CHANGE FLIGHT MODES
.
2.
Power o
ff
the Mamba 10 G2. Insert a bind plug into Aura Port S3
(you will need to remove the servo lead that is currently in S3).
Check the transmitter is on and re-power the Aura to enter
Quick Trim.
3.
Wait 5 seconds for the Aura to completely initialize. Confirm
Quick Trim mode is active by checking the Blue LED is slowly
flashing.
4.
Remove the bind plug from Aura Port S3 to save your trim
settings. Re-install the servo that was previously removed into
port S3. Removing the bind plug stores the current trims in the
Aura. The Blue LED will flash quickly after control surface trim
values are stored. While the trim values are stored in Aura, they
are not applied to the control surface(s) until the Aura is re-
powered.
5.
Remove power from the Mamba 10 G2 and center all control
surface trims on the transmitter.
6.
Re-power the Mamba 10 G2. The control surfaces should be
unchanged even though the trim has been centered on the
transmitter.
7.
Switch between other Flight Modes to ensure you do not see
any changes in trim.
NOTE: QUICK TRIM MAY BE REPEATED AS NEEDED FOR FINE
TUNING, OR IF CHANGES TO THE AIRCRAFT ARE
MADE.
NOTE: ENSURE AILERON/ELEVATOR/RUDDER SUB-TRIMS ARE
ZERO
BEFORE
FLYING FOR QUICK TRIM PROCESS