Fleck 5800 SXT Installation Manual Download Page 5

PAGE 5

Help: 888-426-5001

QualityWaterForLess.com

5) 

 C - UNIT CAPACITY: 

 In the first column, identify the 

section

 containing your softener tank size and then within this 

section, find the 

row

 pertaining to your 

H - Compensated Hardness

 level. Then look under the 

C - Capacity

 column 

to find the most efficient program value to enter for your 

C - Unit Capacity

 and record it 

in the table on page 2.

 

Note that your unit capacity program value may actually be lower than the tank’s rated capacity.

 This is to 

accommodate a lower salt dose for regeneration.

6) 

 BF - BRINE FILL: 

 

In the first column, identify the 

section

 containing your softener tank size and then within this 

section, find the 

row

 pertaining to your

 H - Compensated Hardness

 level. Then look under the 

BF - Brine Fill

 column 

to find the most efficient program value to enter for your 

BF - Brine Fill

 and record it 

in the table on page 2.

 

7) 

 Example: 

 If you ordered a 64K grain capacity system and have 28 gpg compensated hardness, you would look under 

the 64K, 2.0 cu ft section and then look under the 25+ gpg row for your particular programming values. Note that the 
11x11” and the 15x17” brine tanks are too small for the amount of brine needed to regenerate a 64K grain capacity system 
with 25+ gpg hardness. According to the table you would opt for an 18” diameter brine tank with a grid plus 6” legs

Tank Size

HARDNESS

CAPACITY

BF 

BRINE FILL

lbs of Salt

11x11” Grid

15x17” Grid

18x33” Grid

18x40” Grid

24x41” Grid

24x50” Grid

24K 

0.75 cu ft 

8x44”

0 - 12 gpg

15K

6 Min

4.5 lbs

Grid

NO GRID

NO GRID

NO GRID

TOO 

LARGE

TOO 

LARGE

12 - 25 gpg

20K

10 Min

7.5 lbs

Grid

Grid

NO GRID

NO GRID

25+ gpg 

24K

14 Min

11.25 lbs

Grid + 3” Legs

Grid

Grid

Grid

32K 

1.0 cu ft 

9x48”

0 - 12 gpg

20K

8 Min

6 lbs

Grid

NO GRID

NO GRID

NO GRID

TOO 

LARGE

TOO 

LARGE

12 - 25 gpg

27K

14 Min

10 lbs

Grid + 3” Legs

Grid

Grid

Grid

25+ gpg 

32K

20 Min

15 lbs

Grid + 6” Legs

Grid + 3” Legs

Grid

Grid

40K 

1.25 cu ft 

10x44”

0 - 12 gpg

25K

10 Min

7.5 lbs

Grid

Grid

NO GRID

NO GRID

TOO 

LARGE

TOO 

LARGE

12 - 25 gpg

34K

18 Min

12.5 lbs

Grid + 3” Legs

Grid

Grid

Grid

25+ gpg 

40K

26 Min

18.75 lbs

TOO SMALL

Grid + 3” Legs

Grid + 3” Legs

Grid + 3” Legs

48K 

1.5 cu ft 

10x48”

0 - 12 gpg

30K

14 Min

9 lbs

Grid + 3” Legs

Grid

Grid

Grid

TOO 

LARGE

TOO 

LARGE

12 - 25 gpg

41K

20 Min

15 lbs

Grid + 6” Legs

Grid + 3” Legs

Grid

Grid

25+ gpg 

48K

30 Min

22.5 lbs

TOO SMALL

Grid + 6” Legs

Grid + 3” Legs

Grid + 3” Legs

64K 

2.0 cu ft 

12x52”

0 - 12 gpg

40K

16 Min

12 lbs

Grid + 3” Legs

Grid

Grid

Grid

Grid + 

5” Legs

Grid + 

5” Legs

12 - 25 gpg

54K

28 Min

20 lbs

TOO SMALL

Grid + 6” Legs

Grid + 3” Legs

Grid + 3” Legs

25+ gpg 

64K

40 Min

30 lbs

TOO SMALL

TOO SMALL

Grid + 6” Legs

Grid + 6” Legs

80K 

2.5 cu ft 

13x54”

0 - 12 gpg

50K

20 Min

15 lbs

Grid + 6” Legs

Grid + 3” Legs

Grid

Grid

Grid + 

5” Legs

Grid + 

5” Legs

12 - 25 gpg

68K

34 Min

25 lbs

TOO SMALL

Grid + 6” Legs

Grid + 3” Legs

Grid + 3” Legs

25+ gpg 

80K

50 Min

37.5 lbs

TOO SMALL

TOO SMALL

TOO SMALL

Grid + 6” Legs

96K 

3.0 cu ft 

14x65”

0 - 12 gpg

60K

24 Min

18 lbs

TOO SMALL

Grid + 3” Legs

Grid + 3” Legs

Grid + 3” Legs

Grid + 

6” Legs

Grid + 

6” Legs

12 - 25 gpg

81K

40 Min

30 lbs

TOO SMALL

TOO SMALL

Grid + 6” Legs

Grid + 6” Legs

25+ gpg 

96K

60 Min

45 lbs

TOO SMALL

TOO SMALL

TOO SMALL

TOO SMALL

120K 

4.0 cu ft 

16x65”

0 - 12 gpg

80K

32 Min

24 lbs

TOO SMALL

Grid + 6” Legs

Grid + 3” Legs

Grid + 3” Legs

Grid + 

8” Legs

Grid + 

8” Legs

12 - 25 gpg

108K

54 Min

40 lbs

TOO SMALL

TOO SMALL

TOO SMALL

TOO SMALL

25+ gpg 

120K

80 Min

60 lbs

TOO SMALL

TOO SMALL

TOO SMALL

TOO SMALL

Summary of Contents for 5800 SXT

















Reviews: