Flavel Linear Pebble Installation And Maintenance Instructions Manual Download Page 24 | Manualshive

Page: 24 / 24

Flavel Linear Pebble Installation And Maintenance Instructions Manual Download Page 24

Supplied By www.heating spares.co Tel. 0161 620 6677

PARTS SHORTLIST

Replacement of any other parts must be carried out by a competent person such
as a CORGI registered gas installer. The part numbers of the replaceable parts
are as follows, these are available from CFM Europe Ltd. who may be contacted
at the address shown below.

Fuelbed base

B-77260

Fuelbed front rail

B-58140

Replacement pebble set

B-77250

L/H Fibre Board

B-68930

R/H Fibre Board

B-68940

Upper Rear Fibre Board

B-68910

Lower Rear Fibre Board

B-68920

Piezo Igniter

B-1320

Ignition Wire

B-39030

Gas Valve

B-36990

This appliance must only be used with the Linear trim and ashpan
supplied

Due to our policy of continual improvement and development the exact
accuracy of illustrations and descriptions contained in this book cannot be
guaranteed

Part No. B-60310

Issue 5

CFM Europe Ltd.

Trentham Lakes

Stoke-on-Trent

Staffordshire

ST4 4TJ

www.cfm-europe.com

Telephone - General Enquiries :

(01782) 339000

Telephone - Service :

(08700) 101187

«
...
22
23
24

Summary of Contents for Linear Pebble

























Reviews:

No comments