manualshive.com logo in svg

Flaircomm Technologies BLUETONE BTHF102, User Manual, Page: 8 / 17

Share
Download
Flaircomm Technologies BLUETONE BTHF102 User Manual Download Page 8

                                                                    BlueTone

TM 

BTHF102/202 User Manual 

 

 

. 

 

   8  

 

 

2.

 

Using Your Handsfree 

2.1

 

Battery Charging and Usage 

2.1.1

 

Battery Charging 

This device contains a rechargeable Li-Polymer battery. First-time charging time is about 4 hours. Later-on 

recharging time is around 2-3 hours. Detailed charging procedures as follows:  

1.

 

Connect the car charger  to the cigarette lighter. 

2.

 

Referring to Figure 3, plug the connector of the charger to handsfree’s charging port to start charging. Both the 

Red and Blue LEDs will be on during charging. Once the Red LED turns off, the battery is fully charged and 

you should disconnect the charger from the handsfree and the power outlet. 

 

BlueTone

TM

 BTHF102                                                               BlueTone

TM

 BTHF202  

Figure 3 Battery Charging 

2.1.2

 

Battery Information 

1.

 

Once fully charged, the battery for BlueTone

TM 

 BTHF102 supports continuous talk time up to 10 hours and 

standby (i.e. the device is power on but without connection) time about 900 hours; the battery for BlueTone

TM

  

BTHF202 supports continuous talk time up to 5.5 hours and standby  time about 500 hours 

2.

 

When the battery is low, the device beeps once every 20 seconds and the Blue and Red LEDs alternate every 3 

seconds, charge the battery as described above 

Note that, over-charging will reduce battery life. If a fully charged battery is left unused, it will lose power over 

time. Extreme temperature (either too hot or too could) will also affect its ability to charge, capacity, and life time. 

2.2

 

Mounting your Handsfree 

This device comes with a mounting dock and a Double-side Sticker, they can make the device totally laminate in 

front of driver in the vehicle. You can also take the device away from the mounting dock to other places you want. 

Fixing BlueTone

TM 

BTHF102 (referring to Figure 4 and 5)

：

 

1.

 

Tear the paper off from the Double-side sticker, paste it on the back-side of the mounting dock and then fix it 

in front of driver seat on the vehicle. 

2.

 

Plug the stanchion of the mounting dock  to the hole which is on the back of the device,  then rotate deasil, in 

this way, the mounting dock is fixed completely. You also can rotate  widdershins to take down the device 

Summary of Contents for BLUETONE BTHF102


















Reviews:

No comments