FiveFish SK-1DI Assembly Manual Download Page 7

Page: 7 / 47

SK-1DI Mic DI Assembly Guide

3. ASSEMBLY GUIDE

BEFORE YOU BEGIN: Pick a clean work area where you can leave your work-in-progress unattended if you need to.

Keep individual components in their labeled zip bag until you’re ready to solder them. Kit components have been sorted and

labeled for your convenience. The labeled components lessens chances of insertion errors, inserting the wrong component into

the wrong location. Keeping the components in their zip bags also reduces chance of small parts getting lost or misplaced.

Best practice is to solder the smallest and/or shortest components first. Then solder the taller and larger components next. Big

bulkier components like switches, jacks, big capacitors are soldered last.

NOTE: The photos shown on this assembly guide are Rev.1.2 PCBs.

Your PCB Revision may be later but assembly instructions are

generally the same.

Photo of a finished SK-1DI 500 Series Kit

Summary of Contents for SK-1DI






























Search results

Summary of Contents for SK-1DI

Reviews:

Brands by name

Popular brands

FiveFish SK-1DI, Assembly Manual

Search results

Summary of Contents for SK-1DI

Reviews:

Brands by name

Popular brands