background image

11

TURN ON PROCEDURE

1. Set your controls as follows:

GROUND = “10”

DISC = “0” for normal use in target I.D. mode. (Set

DISC to “Autotune” for deep search, all-metal

AUTOTUNE mode.

SENS = “10”

VOLUME = OFF

2. Hold the search coil waist high, away from any

nearby metal.

3. Turn the VOLUME control to “1” (a brief bell tone is

normal when you turn the VOLUME control on).

4. Then increase the volume to a comfortable level

when the search coil passes over a large, shallow

target.

When your CZ-20 QuickSilver is properly “ground balanced,” it will

have only a minimum response to ground mineralization. Precise

adjustment of the GROUND control is critical for optimum

performance. The higher the degree of ground mineralization or the

higher the sensitivity setting,the more critical it is to have your

machine properly ground balanced. Once you adjust it in either

the Autotune mode or Target-I.D. mode, you can switch back and

forth between the two modes without resetting, unless you increase

the sensitivity level or go from dry sand to wet sand or vice versa.

You should also recheck your setting occasionally as you search

because ground conditions often change rapidly.

If you have difficulty ground balancing, try reducing your sensitivity

level or moving to another spot just in case you are over a buried

piece of metal. In some areas of high ground mineralization you

may not be able to use the pushbutton method.

6.  LIGHT EMITTING DIODES (LED’s): Used to indicate

target signal strength. When the SENSITIVITY control is

in the “BATT TEST” position and both LED’s are fully lit

up, the batteries are fully charged. When both LED’s

are out, it’s time to replace the batteries.

GROUND BALANCING

CONTROL PANEL

Summary of Contents for M-Scope CZ-20 QuickSilver











































Reviews: