background image

___________________________________

i

 Batteries 

The F-Pulse operates on 2 AA alkaline, lithium or nickel-metal 

hydride  batteries  (not  included).You  can  use  high  quality 

rechargeable  batteries.  Expect  approximately  25  hours  of 

operation from alkaline batteries. 

Do not use “Zinc-Carbon” or “Heavy-Duty” batteries.
To replace batteries:

1. Use a coin or flathead screwdriver.

2. Rotate counterclockwise to remove cap.

3. Install 2 AA batteries, positive-side down.

4. Rotate clockwise until snug to close and seal.

The battery compartment was designed to provide a snug fit 

for the batteries. If you experience difficulty in removing your 

batteries, tap the pinpointer against the palm of your hand to 

help dislodge the batteries.

CAUTION: Waterproofing requires a tight seal.

 Rotate battery door securely for waterproof seal. 

Low-Battery Warning:

If your batteries are running low and need to be replaced, 

you will hear a boop-boop-boop sound at power-down.

Critical Low-Battery:

If the batteries are totally spent, you’ll hear a boooooop 

sound and the pinpointer will then turn itself off.

Summary of Contents for F-Pulse

















Reviews: