Fisher F-Pulse Owner'S Manual Download Page 14

n

____________________________________

NOTICE TO CUSTOMERS OUTSIDE THE U.S.A.

This warranty may vary in other countries; check with your distributor for 

details. Warranty does not cover shipping costs.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) this device may not cause harmful interference, and (2) this device must accept 

any interference received, including interference that may cause undesired operation.

 

According to FCC part 15.21 changes or modifications made to this device not expressly 

approved by Fisher Research Labs, Inc. could void the user’s authority to operate this 

equipment.

 

Note: This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, 

uses and can radiate radio frequency energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communications. However, there is 

no guarantee that interference will not occur in a particular installation. If this equipment does 

cause harmful interference to radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures:

 

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver. 

—Connect the equipment into an outlet on a circuit different from that to which

    the receiver is connected. 

—Consult the dealer or an experienced radio/TV technician for help.

 

This device complies with Industry Canada license-exempt RSS standard(s). Operation is 

subject to the following two conditions: (1) this device may not cause interference, and (2) 

this device must accept any interference, including interference that may cause undesired 

operation of the device.

 

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio 

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil 

ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique 

subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

www.fisherlab.com

Made in USA from USA and imported parts

Summary of Contents for F-Pulse

















Reviews: