Fisher Design RSS Instruction Manual Download Page 8

Page: 8 / 14

Design RSS

Figure 7. Design RSS Valve Body Shown with Tool

Used to Remove or Install Seat Ring

W4473 / IL

SEAT
RING

SEAT
RING
TOOL

Note

To avoid cold flow of the valve liner and
deforming of the valve body seat ring
threads and seat ring contact surfaces,
promptly install a replacement seat ring
according to step 1 of the

Assembly

procedures.

5. To remove the seat ring (key 4), use the seat ring
tool (figure 7 or 8) that can be ordered from the

Parts

List section or made according to the dimensions in
figure 8 and table 4. To avoid cold flow of the valve
liner and deforming of the valve body seat ring threads
and seat ring contact surfaces, promptly install a re-
placement seat ring according to step 1 of the

Assem-

bly procedures.

Assembly

CAUTION

To avoid damage to the seat ring seal-
ing surface and/or threads in the valve
body liner, make or order the seat ring
tool shown in figures 7 and 8. Installing
the seat ring using other tools might
cause permanent damage to the seat
ring sealing surface and/or threads al-
lowing excessive leakage of the valve.

Table 4. Seat Ring Tool Dimensions

VALVE

SIZE

DIMENSIONS (INCHES)

SIZE,

INCHES

1/2, 3/4

0.781
0.791

1.187
1.197

1.390
1.359

1/4

3/16

0.156
0.150

7-1/2

1.453
1.463

1.859
1.869

2.156
2.187

1/4

3/16

0.312
0.300

7-1/2

1-1/2

2.125
2.135

2.515
2.525

2.828
2.859

9/32

7/32

0.312
0.300

8-3/4

2.562
2.572

3.000
3.010

3.296
3.328

9/32

7/32

0.312
0.300

8-3/4

3.593
3.603

4.093
4.103

4.406
4.437

9/32

7/32

0.312
0.300

11-7/8

4.171
4.181

4.656
4.666

4.968
5.000

9/32

7/32

0.312
0.300

11-7/8

VALVE

SIZE

DIMENSIONS (MILLIMETERS)

SIZE,

INCHES

1/2, 3/4

19.84
20.09

30.15
30.40

35.31
34.52

6.35

4.76

3.96
3.81

190.50

36.91
37.16

47.22
47.47

54.76
55.55

6.35

4.76

7.92
7.62

190.50

1-1/2

53.98
54.23

63.88
64.13

71.83
72.62

7.14

5.55

7.92
7.62

222.25

65.07
65.33

76.20
76.45

83.72
84.53

7.14

5.55

7.92
7.62

222.25

91.26
91.52

103.7
104.2

111.91
112.70

7.14

5.55

7.92
7.62

222.25

105.94
106.20

118.2
118.5

126.19
127.00

7.14

5.55

7.92
7.62

222.25

Figure 8. Seat Ring Tool

A3520–1 / IL

Summary of Contents for Design RSS















Search results

Summary of Contents for Design RSS

Reviews:

Fisher Design RSS, Instruction Manual, Page: 8 / 14

Search results

Summary of Contents for Design RSS

Reviews: