manualshive.com logo in svg

Fisher Control-Disk, Instruction Manual

Share
Download
Fisher Control-Disk Instruction Manual Download Page 19

Instruction Manual

D103298X012

Control-Disk Valve

June 2017

19

Figure 9. Lever/Shaft/Disk Orientation with Valve Closed

ACTUATOR

MOUNTING

STYLE

VALVE CLOSED

MOUNTING
POSITION 1

NOTES:

 WHEN ONE IS FACING THE INLET, THE ACTUATOR IS TO THE RIGHT OF THE VALVE BODY.

 WHEN ONE IS FACING THE INLET, THE ACTUATOR IS TO THE LEFT OF THE VALVE BODY.

 FOR 60‐DEGREE OPERATION WITH PUSH‐DOWN‐TO‐CLOSE ACTION (EXTENDING ACTUATOR ROD CLOSES VALVE), ROTATE ACTUATOR LEVER COUNTERCLOCKWISE SO THAT LEVER INDEX
MARK IS OFFSET 1 SPLINE TOOTH FROM VALVE SHAFT INDEX MARK FOR NPS 2 THROUGH 4 VALVES AND 2 SPLINE TEETH FROM VALVE SHAFT INDEX MARK FOR NPS 6 THROUGH 12 VALVES.

 CURVED ARROWS IN ”VALVE CLOSED' COLUMN INDICATE ROTATION REQUIRED TO OPEN VALVE (COUNTERCLOCKWISE WHEN VIEWED FROM ACTUATOR SIDE OF VALVE).

 ARROWS IN ”MOUNTING POSITION'' COLUMNS INDICATE DIRECTION OF ACTUATOR ROD TRAVEL REQUIRED TO OPEN VALVE.

6. PDTC—PUSH DOWN TO CLOSE; PDTO—PUSH DOWN TO OPEN.

RIGHT-
HAND

STYLE A
(PDTO)

STYLE B
(PDTC)

STYLE C
(PDTC)

STYLE D
(PDTO)

LEFT-
HAND

FORWARD
FLOW

43A5323‐B
B1125‐1

1

2

3

4

5

MOUNTING
POSITION 2

5

MOUNTING
POSITION 3

5

MOUNTING
POSITION 4

5

1

3

2

3

4

5

FORWARD
FLOW

FORWARD
FLOW

FORWARD
FLOW

ACTUATOR ROD

ACTUATOR ROD
END BEARING

ACTUATOR LEVER

LEVER INDEX
MARKS (4)
VALVE SHAFT
INDEX MARK

TYPICAL ACTUATOR (FISHER 1052)

SECTIONAL THROUGH HOUSING

A3344

Summary of Contents for Control-Disk

























Reviews:

No comments

Brands by name

Popular brands

Load more brands