background image

11

Battery Safety Information

Setup and Use

Batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different

types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always

remove exhausted batteries from the product. Dispose of 
batteries safely. Do not dispose of batteries in a fire. 
The batteries may explode or leak.

• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type 

as recommended.

• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product 

before charging.

• If removable, rechargeable batteries are used, they are 

only to be charged under adult supervision.

WARNING

To prevent serious injury or death
from falls and being strangled in
the restraint system:

• Always use the restraint system.

Never rely on the tray to restrain child.

• Never use with an active child who

may be able to climb out of the seat.

• Not recommended for children who

can sit up by themselves (6 months
approximately, until 9 kg (20 lbs).

• Never leave the child unattended.
• It is dangerous to use this product

on an elevated surface.

IMPORTANT!

Before each use, inspect this product for damaged

hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Mattel for replace-
ment parts and instructions if needed. Never substitute parts.

Summary of Contents for H5988

















Reviews: