background image

7

B

e

 IMPORTANT INFORMATION  

S

 INFORMACIÓN DE IMPORTANCIA  

f

 RENSEIGNEMENTS IMPORTANTS

M3576pr-0726

BATTERY CHARGING

E

Important Notes

• 

Your new battery must be charged for at least 18 hours before 
you use it in your vehicle for the first time.

•  We recommend that you start charging your battery before beginning 

assembly of your new vehicle. 

•  The battery must be upright while charging.
•  The charger is not a toy.
•  Do not short circuit the battery.
•  You do not need to remove the battery from your vehicle to 

recharge it.

•  Before charging the battery, examine the battery case for cracks and 

other damage which may cause sulfuric acid (electrolyte) to leak 
during the charging process. If damage is detected, do not charge 
the battery or use it in your vehicle. Battery acid is very corrosive and 
can cause severe damage to surfaces it contacts. 

•  Do not charge the battery on a surface (such as a kitchen counter 

top) which could be damaged by the acid contained inside the 
battery. Take precautions to protect the surface on which you charge 
your battery. 

•  Use only a Power Wheels

®

 12 volt charger with "12V" connector

(240 VAC, 50 Hz with an output of 12 VDC, 1200 mA) to charge your 
Power Wheels

®

 12 volt battery.

Adults Note:

 Regularly examine the charger for damage to the

cord, plug, housing or other parts that may result in the risk of fire, 
electric shock or injury. In the event of any damage, do not use the 
charger until the damage has been properly repaired. Please contact 

01628 500303

 or visit us on-line at 

www.service.mattel.com/uk

.

•  If your battery is old and will not accept a charge, do not leave it in 

the vehicle. Always remove a dead battery from the vehicle.

About Thermal Fuses

Your Power Wheels

®

 12 volt battery is equipped with a built-in 

thermal fuse. The thermal fuse is a self-resetting safety device which 
automatically “trips” and shuts down operation of the vehicle if the 
vehicle is overloaded or the driving conditions too severe. Once a fuse 
has “tripped”, remove your foot from the pedal and wait approximately 
25 seconds before operating the vehicle again. To avoid repeated 
automatic shut-downs, do not overload the vehicle by exceeding the 
59 kg (130 lbs) maximum weight capacity or by towing anything behind 
the vehicle. Avoid severe driving conditions, such as driving up slopes 
or running into fixed objects, which can cause the wheels to stop 
spinning while power is still being supplied to the motors and make 
sure your child stops the vehicle before switching direction.
If a thermal fuse in a battery continually trips under normal driving 
conditions, please contact 

01628 500303

 or visit us on-line at 

www.service.mattel.com/uk

.

CAUTION

ELECTRICAL HAZARD

• Battery can fall out and injure a child if 

vehicle tips over. Always use battery
retainer.

• 

PREVENT FIRE

 -  

Never modify the electrical system. 
Alterations could cause a fire resulting 
in serious injury and could also ruin the 
electrical system.

 -  

Use of the wrong type battery or charger 
could cause a fire or explosion resulting 
in serious injury.

 -  

 Use of Power Wheels

®

 components in 

products other than Power Wheels

®

 

vehicles could cause overheating, fire 
or explosion.

•  The battery must be handled by adults 

only. The battery is heavy and contains 
sulfuric acid (electrolyte). Dropping the 
battery could result in serious injury.

• Never allow children to charge the battery. 

Battery charging must be done by adults 
only. A child could be injured by the elec-
tricity involved in charging the battery.

• Read the safety instructions on the battery.
• Examine the battery, charger and their 

connectors for excessive wear or damage 
each time you charge the battery. If 
damage or excessive wear is detected, do 
not use the charger or the battery until you 
have replaced the worn or damaged part.

WARNING

Use the charger in dry locations only.

Summary of Contents for DORA JEEP WRANGLER M3576





























Reviews: