background image

16

FCC Statement (United States Only)

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more of the 
following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver 

is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Note:

 Changes or modifications not expressly approved by the manufacturer responsible 

for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) this device may not cause harmful interference and (2) this device 
must accept any interference received, including interference that may cause 
undesired operation.

ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to 
the following two conditions: (1) this device may not cause harmful interference and 
(2) this device must accept any interference received, including interference that may cause 
undesired operation.

NMB-003

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 
(1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à 
accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de 
compromettre le fonctionnement du dispositif.

Consumer Information 

Summary of Contents for BFX34

















Reviews: