background image

Care

Storage

• Fit the bottom of the remote into the

cupped portion of the holder.

• Push to 

“snap”

the top of the remote

under the holder clips.

• Turn the toybar back to its storage position.
• Press the button on the inside of each housing and push the

rear legs toward the front legs. Stand the frame against a
wall for storage.

To remove the pad:

• Unhook the four elastic hooks from the pegs on the seat

back and bottom.

• Push the restraint belts back through the slots in the pad.
• Slide the upper pad pocket off of the seat back.
• Slide the lower pad pocket off of the seat bottom.

To replace the pad:

• Refer to Assembly steps 19 - 21.

Note:

This product has no consumer serviceable parts. Do not

take this product apart.

The pad is machine washable. Wash the pad separately in cold
water on the gentle cycle. Do not use bleach. Tumble dry sep-
arately on low heat and remove promptly. The frame, tray and
toybar may be wiped clean using a mild cleaning solution and
a damp cloth.

15

Restraint

Belts

Upper

Pad

Pocket

Lower

Pad

Pocket

Elastic

Loops

Elastic

Loops

Press

Buttons

Clips

B0323 Quick Response Swing  9/24/02  1:03 PM  Page 15

Summary of Contents for B0323

















Reviews: