background image

6

A

B

C

D

F

G

M

M

M

N

N

O

O

H

I

J

K

L

E

M

M

M

N

O

A

B

C

D

F

G

M

M

M

N

N

O

O

H

I

J

K

L

E

M

M

M

N

O

5B

   CABINETRY DIMENSIONS - WALL MOUNTED (IE INSTALLED WITH A F&P COMPACT OVEN)

600mm

*PO

Tab

Unscrew-fit- 
rescrew

PLAN

SIDE

CABINETRY DIMENSIONS

mm

M

Minimum inside height of cavity 
   with optional Lower trim kit fitted
   without optional Lower trim kit fitted

590

570

N

Inside width of cavity

560

O

Minimum inside depth of cavity

565

Note: When installed in combination with a companion product the companion product may be placed directly onto the 
warming drawer. It is not necessary to place a shelf between the products. A built- in shelf at the base of the cabinetry able 
to support the weight of both products is required.

* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.

Compact Oven

Compact Oven

Cabinet below

Additional 18 mm Wood Spacer 

Warming Drawer

Lower trim kit 
(optional, supplied separately)

Compact oven

IMPORTANT!

In a wall mounted installation, 

there needs to be an 18 mm 

Spacer fixed underneath the 

warming drawer first to raise 

it to the required height. 

Warming Drawer

Warming Drawer

Summary of Contents for WB60S Series

















Reviews: