manualshive.com logo in svg

Fisher & Paykel RS6121VL2K1, Installation Manual

Share
Download
Fisher & Paykel RS6121VL2K1 Installation Manual Download Page 3

3

CONTENTS

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, 

go to our website fisherpaykel.com or contact your local Fisher & Paykel dealer.

SAFETY AND WARNINGS 

4

INTEGRATED COLUMNS — WINE CABINET 

5

COMPONENTS 6
DOOR PANEL AND HANDLE SETS 

8

WINE DISPLAY ACCESSORIES 

9

TOOLS 9
APPLIANCE DIMENSIONS 

10

CAVITY DIMENSIONS 

11

DOOR PANEL DIMENSIONS 

13

TOE KICK PANEL DIMENSIONS 

14

CUSTOM DOOR PANEL DIMENSIONS 

15

DOOR CLEARANCE 

16

ELECTRICAL DIMENSIONS 

17

ELECTRICAL SPECIFICATIONS 

18

BEFORE INSTALLATION 

19

Check your appliance 

19

Move your appliance 

19

Check the installation location 

20

INSTALL ANTI-TIP BRACKET 

21

CONNECT TO POWER SUPPLY 

22

ATTACH DEPTH ALIGNMENT GAUGES 

23

POSITION APPLIANCE INSIDE THE CABINETRY 

24

Attach barbed plugs 

24

ALIGN APPLIANCE INSIDE THE CABINETRY 

25

Align depth gauges with cabinetry 

25

Adjusting appliance inside the cabinetry 

26

FIX APPLIANCE INSIDE THE CABINETRY 

27

INSTALL CARBON FILTER 

28

PREPARE FOR DOOR PANEL INSTALLATION 

29

Removing hanging bracket 

29

Attaching door handle 

30

Attaching hanging bracket and side brackets 

30

Attaching long glass trims 

31

Attaching short glass trims 

32

INSTALL DOOR PANEL 

33

Hanging door panel 

33

Adjusting door panel 

34

INSTALL TOE KICK MOUNTING PLATE 

35

Adjusting toe kick grille 

35

Installing toe kick mounting plate 

35

INSTALL TOE KICK AND GRILLES 

36

Installing toe kick 

36

Attaching top and bottom grilles 

36

INSTALL CABINET TRIMS 

37

Re-installing top trim 

37

Re-installing flow divider 

37

Installing side trims 

38

INSTALL DOOR TRIMS 

39

WINE DISPLAY 

40

OPTIONAL — CHANGE DOOR HINGES 

41

Removing the door 

41

Removing top door hinge 

42

Removing bottom door hinge 

42

Moving the sensor housing 

43

Top hinge installation 

44

Bottom hinge installation 

44

Door brackets 

45

Door installation 

46

FINAL CHECKLIST 

47

Summary of Contents for RS6121VL2K1

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands