manualshive.com logo in svg

Fisher & Paykel RS6121VL2K1, Installation Manual

Share
Download
Fisher & Paykel RS6121VL2K1 Installation Manual Download Page 45

45

Hinge change 

assembly

 

K05 top adaptor 
bracket R/L (1)

 

K05 bottom adaptor 
bracket R/L (1) 

Tools

T2 star-head screwdriver

Flat-head screwdriver

OPTIONAL — CHANGE DOOR HINGES

Door brackets

A

D

C

(use new top 

adaptor bracket)

B

E

F

(use new bottom adaptor 

bracket and spacer)

(use existing locking bracket)

Remove the top adapter bracket from the top of the door 
by unscrewing M5x10 screws (4x) (

A).

1

Install the 

new

 top adapter bracket into the other side of 

the top of the door with M5x10 screws (4x) (

B).

2

Remove the door panel locking bracket and washer from 
the bottom of the door by unscrewing M6x25 screw (1x) (

C).

3

Remove the bottom adapter bracket and spacer from the 
bottom of the door by unscrewing M6x25 screws (2x) 
and M5x30 screw (1x) (

D).

4

Install the 

new

 bottom adapter bracket and existing 

spacer to the other side of the door with M6x25 screws 
(2x) and M5x30 screw (1x) (

E).

5

Install the existing door panel locking bracket and washer 
to the other side of the door with M6x25 screw (1x) (

F

).

6

Summary of Contents for RS6121VL2K1

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands