Fisher & Paykel PHASE 7 INTUITIVE ECO IWL16-US Service Manual Download Page 6

517793A 

 

 

1.7 Water 

Valves 

Supply

 

Mode of Operation

 

Voltage

 

Resistance

 

Flow Rate

 

Cold 

Digitally Operated 

24V DC 

64

 @ 68

 o

F / 20

o

16 liters per minute 

Hot Digitally 

Operated

 

24VDC 64

 @ 68

 o

F / 20

o

10 liters per minute 

 
Note: Flow rate will vary slightly depending on pressure. 

 
Operating pressures: 

Maximum 150psi / 1034 kPa - Minimum 5psi / 34 kPa  

  

Note:  Pressures below 5psi / 34kPa can create seating problems with the internal 
diaphragm of the valve, and may cause water to drip into the inner basket when the 
machine is not in use. 

 

1.8 Thermistor 

NTC-type temperature sensor (Thermistor) 

Resistance 10,000

 @ 77

 o

F / 25

o

 

1.9 Cabinet 

Pre-painted steel 

1.10 Lid 

 

ABS plastic (co-injected) 

1.11 Top 

Deck 

Polypropylene 

1.12 

Inner Basket  

Stainless steel: Grade 430T 
Basket base and balance ring: Polypropylene 
 
The inner bowl on the large machine has a 
series of small bumps around the base of the 
inner bowl.  These bumps are designed to 
improve wash performance by increasing load 
turnover and movement. 
 

Note: The inner bowl is backwardly 
compatible with all earlier large machines.   

 
 

 

 

Inner Basket Weight 

Large 

23.10lb +/- 9.7oz / 10.480kg +/- 275g 

 

Inner basket speed 

Fast Spin 

1,000 RPM 

Medium Spin 

670 RPM 

Slow Spin 

300 RPM 

Stir Speed 

25 RPM 

 

Summary of Contents for PHASE 7 INTUITIVE ECO IWL16-US















Reviews: