Fisher & Paykel PHASE 7 INTUITIVE ECO IWL16-US Service Manual Download Page 5

517793A 

 

 

1 SPECIFICATIONS 

 

1.1 Dimensions 

Height to lid 

 

Open 

55.5in – 56.6in / 1410mm – 1440mm 

Closed 

37.4in – 38.5 / 950mm – 980mm 

Height to console 

39.7in – 41.3in / 1010mm – 1050mm 

Width 

25.5in / 650mm  

Depth 

25.5in / 650mm 

Inlet hose length 

47.24in / 1200mm 

Packed weight 

143.3lb / 60.5kg  

Unpacked weight 

114.64lb / 52.0kg 

 

Note:  Exact height of the machine is dependent on how far the feet are inserted into the 
base of the machine. 

1.2 

Maximum Capacity (Full Load) 

Dry Weight 

17.6lb / 7.5kg 

1.3 

Water Consumption  

Fill (High) 

23.7 gal / 90 liters 

Spray & Deep Rinse 

34.3 gal / 175 liters 

Save Water 

39.6 gal / 150 liters 

Eco Rinse 

27.7 gal / 105 liters 

1 Deep Rinse 

43.5 gal / 165 liters 

2 Deep Rinse 

56.79 gal / 215 liters 

*Note:  Approximate water consumption for a high water level load for each rinse option 
offered. 
 

1.4 

Water Fill Temperature (Approximate Factory 
Settings) 

Supply 

Water Fill Temp 

Hot 140

o

F / 60

 o

Hot / Warm 

122

 o

F / 50

 o

Warm 104

 o

F / 40

 o

Warm / Cold 

95

 o

F / 35

 o

Cold Plus 

68

 o

F / 20

 o

Cold Supply 

temperature 

Recommended hot water inlet temperature 149

 o

F / 65

 o

C. (Max)

 

 

1.5 Wash 

Motor 

Electronically commutated direct drive 3 Phase brushless DC Motor’ 36 Poles. 
Motor Resistance per Phase 16

 +/- 10% @ 68

 o

F / 20

 o

C.   

 

1.6 Pump 

Motor 

Part Number

 

Voltage

 

Frequency

 

Resistance

 

420325P 110V 

AC 60Hz 7

 +/- 8% @ 68

 o

F / 20

o

Note: Thermal cut-out fitted 

Summary of Contents for PHASE 7 INTUITIVE ECO IWL16-US















Reviews: