manualshive.com logo in svg

Fisher & Paykel FabricSmart WA1068P, Installation Manual

Share
Download
Fisher & Paykel FabricSmart WA1068P Installation Manual Download Page 12

12

BEFORE YOUR FIRST WASH

Before you start, mark ( 

 ) accordingly if you have gone through

the checklist below: 

1 

Has the basepacker been removed?

2 

Is the drain hose threaded through the hose guide ‘U bend’ (with no more 
than 20mm extended) and hooked into your standpipe or tub, or attached 
to a spigot?

3 

Is the hot hose connected to the hot valve marked ‘H’?

4 

Is the cold hose connected to the cold valve marked ‘C’?

5 

Have the taps been turned on?

6 

Is the machine correctly levelled, feet are extended and cabinet corners are 
clear of the floor?

7 

Has the power cord been connected to an appropriate power supply and the 
power turned on?

8 

Have you performed the installation test cycle? Refer ‘Installation 
instructions’ page. 

FabricSmart™ capacity

FabricSmart™ offers a very generous 10 kg capacity. The list below outlines what is included 
in a 10 kg wash load (in accordance with AS / NZS 2040.1:2005).

Note: The above load composition is indicative only. We recommend for everyday use that 
you separate out your sheets and towels and wash them separately on the 

REGULAR

 cycle.

WASH LOAD - 10 KG

QUANTITY

Sheets (double)

4

Bath towels

8

Tablecloths

3

Shirts

4

T-Shirts

6

Pillowcases

6

Shorts

6

Washcloths

4

Handkerchiefs

2

Summary of Contents for FabricSmart WA1068P























































Reviews:

No comments

Brands by name

Popular brands

Load more brands