8
EN
VENTILATION SYSTEM
Step
3
(A) Rotate 180˚
(B)
Figure 9
z
Rotate the Hood Fan Unit 180˚ so that
the fan blade openings are facing the
back of the oven. Note, you will need to
lift the wire over the hood fan unit so the
wire will clear. See Figure 9 (A). Replace
Hood Fan Unit into the oven. Be careful
not to pinch the wire and the Hood Fan
Unit. See Figure 9 (B).
Step
4
Put the wire back into the cavity.
Step
5
Wire Box
Figure 10
z
Replace the fan cover bracket. Make sure
the fan blades are visible through the
rear openings in oven before proceeding.
Attach the fan cover bracket to the
unit with the 4 screws removed in step
1 above. See Figure 10. The hood fan
is now rotated for horizontal exhaust
operation.
Step
6
Mounting Plate (back side)
Figure 11
z
Attach the Exhaust Damper Assembly
to the back of the mounting plate
by sliding it into the slits in the same
direction as the arrow. See Figure 11.
Using tapping screw 4 x 12 mm from the
INSTALLATION HARDWARE, tighten into
place.
C. VERTICAL VENTILATION - OUTSIDE VENTILATION
Step
1
Fan Cover Bracket
Figure 12
z
Remove and save the 4 screws from the
Fan Cover Bracket. Remove Fan Cover
Bracket by sliding it in the opposite
direction of the arrow on the Fan Cover
Bracket as shown in Figure 12.
Step
2
Figure 13
z
Lift the Hood Fan Unit carefully and slip
wires out of cavity. See Figure 13.
CAUTION:
DO NOT PULL OR STRETCH BLOWER WIRING
Step
3
(A) Rotate 180˚
(C)
(B)
Figure 14
z
Rotate the Hood Fan Unit 180˚ so that
the fan blade openings are facing the
back of the oven. Note, you will need to
lift the wire over the hood fan unit so the
wire will clear. See Figure 14 (A). Then
rotate the Hood Fan Unit 90˚ so that the
fan blade openings are facing the top
of the oven. See Figure 14 (B). Replace
Hood Fan Unit into the oven. Be careful
not to pinch the lead wire between the
inner bracket and the Hood Fan Unit. Put
the lead wire into Wire Box. See Figure
14 (C).
Step
4
Replace the Fan Cover Bracket. Make sure the fan blades are visible through the top
openings in the oven before proceeding.
EN
9
VENTILATION SYSTEM
Step
5
Wire Box
Figure 15
z
Attach the Fan Cover Bracket to unit
with the 4 screws removed in step 1
above. See Figure 15. The Hood Fan
Unit is now rotated for vertical exhaust
operation.
Step
6
Exhaust Damper Assembly
Figure 16
z
Attach the Exhaust Damper Assembly
to the fan cover on the top of the
outercase cabinet by sliding it into the
slits in the same direction as the arrow.
Use 1 Tapping Screw 4 x 12 mm from the
INSTALLATION HARDWARE and tighten
into place. See Figure 16.
OVEN INSTALLATION
This oven cannot be properly installed without referring to the mounting instructions found on
both templates.
Read and follow mounting information on both
TOP CABINET TEMPLATE
and
WALL TEMPLATE
.
MOUNTING PLATE
Step
1
z
Separate 4 Toggle Bolts
2
, packed in the INSTALLATION HARDWARE, from the
Toggle Nuts.
Step
2
Mounting Plate
Figure 17
z
Use Wood Screws
1
to attach Mounting
Plate to the stud or studs. Use Toggle
Bolts to attach Mounting Plate through
the holes at A, B, C and D; UNLESS
THOSE HOLES ARE LOCATED ON THE
STUD. Insert one Toggle Bolt into A,
B, C and D where appropriate (these
correspond to the holes of the Wall
Template) and put the Toggle Nuts onto
the Toggle Bolts. Figure 17.
Refer to instructions in Wall Template.
Step
3
Wall
Space more than
wall thickness
Figure 18
z
Position the Mounting Plate with the
Toggle Bolts attached at the wall location
and insert Toggle Nuts and Bolts through
the holes in the wall with the Toggle Nuts
closed. Figure 18. Use Wood Screws
1
to
attach the Mounting Plate to studs.
Note:
Before insertion, be sure you leave a
space more than the thickness of the wall
between the Mounting Plate and the end
of each of the Toggle Nuts (in the closed
position). If you do not leave enough space,
the Toggle Nut will not be able to open
on the other side of the wall. Also, once a
Toggle Nut opens, it cannot be withdrawn
from the hole; therefore make sure all of the
Toggles are in the correct position before
insertion.
Step
4
Figure 19
z
Align the Mounting Plate carefully and
hold in position while tightening Toggle
Bolts. Pull Toggle Bolt toward you and
turn clockwise to tighten. Figure 19.
