Fisher & Paykel AS/NZS 1044 Installation Instructions Manual Download Page 7

Page: 7 / 10

Fig. 12 Unhooking the terminal block cover

Fig. 13 Connection diagram

Fig. 14 Fixing the power supply cable

Connecting the power supply cable - CE604 models

1. Turn the cooktop over and place it on a soft surface.

2. Unhook the terminal board cover by inserting a screwdriver into the two hooks C (fig. 15).

3. Unscrew the screw D and open completely the cable clamp E (fig. 17).

4. Check the bridging links F are inserted into terminal block A as shown (Figs. 16 - 17).

5. Connect the phase, neutral and earth wires to terminal board A according to the diagrams in figs. 16 - 17.

6. Strain the feeder cable and block it with cable clamp E (by screwing screw D).

7. Close the terminal block cover (check the two hooks C are correctly hooked).

To connect the power supply cable DO NOT unscrew the screws fixing the cover plate B
behind the terminal block.

Power supply special cable section type “H05V2V2-F” or equivalent rated minimum V-90.

Resistance to temperatures of 90°C

• 230-240 V~ 6000-6500 W 50 Hz (27A)

https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions

Updated: Sat, 09 Mar 2019 07:23:30 GMT

Summary of Contents for AS/NZS 1044










