background image

10

15

OPERATION and CONTROLS

While in 

DISCRIMINATE

or

ALL-METALS 

mode,

press and hold

the Pinpoint button to

actuate 

PINPOINT

.

While in 

GROUND GRAB

mode, press and hold

the Pinpoint button to

actuate 

GROUND GRAB

.

Press

MENU

button

to select the

menu item you

want to adjust.

Press

MODE

button

to

TOGGLE

between

the Discrimination and

All-Metals modes.

POWER

ON/OFF

Press

or

Buttons

to

CHANGE THE SETTING

of the active menu item.

The active menu item is

the Highlited line on the

left side of the display.

Press

or

Buttons

to

CHANGE THE SETTING

of the active menu item.

The active menu item is

the Highlited line on the

left side of the display.

HOW TO WORK THE CONTROLS

POWERING UP

Press 

• The detector always starts in the DISCRIMINATION mode.

Motion is required.

• Sensitivity is at about 70% of maximum (value reads “80”)
• All target categories are illuminated, meaning that all metal objects will

be detected.

OPERATION and CONTROLS

cont.

MODE SELECTIONS

There are four selections under the MODE section of the display.

• Press

to toggle between DISCRIMINATION, ALL METALS and

GROUND GRAB.

• While operating in the DISCRIMINATION or ALL METALS mode, press

to activate PINPOINT mode.

• While operating in the GROUND GRAB mode, press 

to

automatically ground balance the detector.

1. DISCRIMINATE Mode

This mode is the default mode, and requires the searchcoil to be in motion in
order to detect and identify targets. This is the mode most commonly used for
continuous searching.  In this mode, targets are identified with distinct tones,
and are classified in categories at the top of the display.  A two-digit numerical
value, on a scale of 10 to 99, is displayed in the middle of the screen. The
depth range of the target is also displayed at the bottom of the display.  All
menu items can be selected and customized in this mode.

2. ALL METALS Mode

This mode is similar to the “Fast Autotune” or “SAT™” mode found in other
detectors. Only the SENSITIVITY and VOLUME menu items are adjustable in
this mode. 

3. PINPOINT

To activate this mode, you must first be in either the DISCRIMINATION or ALL
METAL mode.  Press and hold 

to activate pinpoint.  This mode is

momentary; pinpoint detection is only active for as long as you keep 
depressed. 

Metal targets are detected with the searchcoil motionless over the target.
Target identification is not possible in this mode.  All metal objects will induce
a single monotone hum.  The 2-digit value in the middle of the screen
represents the approximate target depth, in inches.

Pinpoint is used to find the exact location of a target which was previously
located and identified using the discrimination mode.  As this mode does not
require motion over the target, the user can move the coil more slowly and
then narrow the detection field when near the target.

Summary of Contents for Gamma 6000

























Reviews: