First Degree Fitness fluid e820 Fitness UBE Owner'S Manual Download | Manualshive

Page: 8 / 27

background image

8

Step One:

Stand Baseplate upright to install 4x Foot levelers as shown.

Once foot levelers are installed, the completed baseplate can be
installed onto the mainframe of the E820.

Install Baseplate to Mainframe

Step Two:

Mount the baseplate onto

the Mainframe using mounting pins as
a locator

Then, secure with 3x M10x25mm Bolt,
2x M10 Nylock Nut and 3x M10
Washer
Note center M10 Bolt does not require
Nut.

Foot leveler

Completed
Baseplate

Baseplate to Mainframe.
3x M10x25mm Bolts, 3x
M10 Washer and 2x M10
Nylock Nuts.

Mounting pins on
E820 Mainframe

«
...
6
7
8
9
10
...
»

Summary of Contents for fluid e820 Fitness UBE




























Reviews:

No comments

Related manuals for fluid e820 Fitness UBE

Brand: Taurus Pages: 52

Brand: Cubii Pages: 22

SuperMagneto Pro

Brand: CycleOps Pages: 10

Brand: x-erfit Pages: 18

Brand: BH FITNESS Pages: 17

Brand: BH FITNESS Pages: 49

Brand: BH FITNESS Pages: 51

Brand: BH FITNESS Pages: 52

Brand: BH FITNESS Pages: 59

Brand: BH FITNESS Pages: 58

Brand: Pro-Form Pages: 18

Brand: Hammer Pages: 22

Brand: HMS Pages: 56

Brand: HMS Pages: 70

Brand: HMS Pages: 68

Brand: Merach Pages: 19

Momentum 635 Elliptical

Brand: Weslo Pages: 20

Brand: Vision Fitness Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands