FIREWOLF FW-DACT, Installation & Operation Manual

Page: 10 / 16

Page 8
Items accessible to LevelII only
ITEM Access Menu Menu Label Description
Number Level Category
30 II Account (#1) Account ID #1 Assign 4-6 numeric Account ID to be identified with Account #1
monitoring station receiver.
31 II Account (#1) Dial-Prefix #1 (OPTIONAL) Set up-to-8-digits to be first dialed by DACT when
attempting to call Account #1 monitoring station receiver.
32 II Account (#1) Local Number #1 Set up-to-8-digits to be dialed (after Dial-Prefix #1 digits) by
DACT when attempting to call Account #1 monitoring station
receiver.
33 II Account (#1) Report Format #1 Choose report format (Contact ID or SIA) to be generated by
DACT when reporting with Account #1 monitoring station
receiver.
40 II Account (#2) Account ID #2 Assign 4-6 numeric Account ID to be identified with Account #1
monitoring station receiver
41 II Account (#2) Dial-Prefix #2 (OPTIONAL) Set up-to-8-digits to be first dialed by DACT when
attempting to call Account #2 monitoring station receiver.
42 II Account (#2) Local Number #2 Set up-to-8-digits to be dialed (after Dial-Prefix #2 digits) by
DACT when attempting to call Account #2 monitoring station
receiver.
43 II Account (#2) Report Format #2 Choose report format (Contact ID or SIA) to be generated by
DACT when reporting with Account #2 monitoring station
receiver.
50 II Report Priority ALARM Events Choose which Account # (1 or 2) will be the first to be
attempted to be reached by the DACT, when an ALARM event is
to be reported. This is designated as the “primary ” account and
the other will become the “secondary”. If the DACT cannot
report to the primary, it will then
attempt to report to the
secondary. This cycle will normally continue until the event is
eventually or the <MAXIMUM Attempts> has been achieved.
51 II Report Priority TROUBLE Events Choose which Account # (1 or 2) will be the first to be
attempted to be reached by the DACT, when a TROUBLE event
is to be reported. (See ITEM 50 for a description of the DACT
report-attempt operation).
52 II Report Priority SUPERVISORY Choose which Account # (1 or 2) will be the first to be
Events attempted to be reached by the DACT, when a SUPERVISORY
event is to be reported. (See ITEM 50 for a description of the
DACT report-attempt operation).
53 II Report Priority ‘Must’ Report #1 The selection allows the overriding of the “normal’ reporting
fulfillment strategy. If ‘Must’ Report #1 is ALWAYS, the DACT will
continue to
attempt to report each event to Account #1 until
successful . This will be the case even if the event has been
previously reported to Account #2, and even if the DACT has
also exceeded MAX attempts. (see ITEM 55).
54 II Report Priority ‘Must’ Report #2 The selection allows the overriding of the “normal’ reporting
fulfillment strategy. If ‘Must’ Report #2 is ALWAYS, the DACT will
continue to
attempt to report each event to Account #2 until
successful . This will be the case even if the event has been
previously reported to Account #1, and even if the DACT has
also exceeded MAX attempts. (see ITEM 55).
55 II Report Priority Max. Attempts Set the “normal” upper limit for DACT attempts (call-attempt
pairs) to report to monitoring station receivers.(See ITEM 50 for a
description of the DACT report-attempt operation). After this
count has been exceed, the DACT will assert the TROUBLE-
SEND signal (and BUZZER) to the connected Fire-Panel.
60 II Phone Line Dial-type Line 1 Configure Line 1 for DTMF (Tone) or Rotary (Pulse) dialing. The
(1/2) choice of which line to be used when the DACT is reporting
normally alternates between Line 1/2 with each call-attempt.
61 II Phone Line Dial-type Line 2 Configure Line 2 for DTMF (Tone) or Rotary (Pulse) dialing. The
(1/2) choice of which line to be used when the DACT is reporting
normally alternates between Line 1/2 with each call-attempt.