background image

 

564 SS & 25K Fireback Installation 

96100179, 96100187, 96100192, 96100270, 96100204

 

 

Page 1 of 6 

17601465 - 1/23/20 

Travis Industries, Inc.  

Compatibility 

 564 

SS 

 564 

25K 

 

564 25k CF 

 

Packing List 

 Rear 

Fireback 

 

(2) Side Firebacks 

 

(2) Floor Firebacks 

 

The firebacks are fragile (especially the rear fireback).  Take care when handling the firebacks. 

 

WARNING

 

Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.  

 

564 25K (Standard or CleanFace) Installation 

(for 564 SS units see page 5) 

NOTE

  On two-sided firebacks make sure to use the desired pattern. 

NOTE:  If using an optional fireback install the kit prior to performing any other firebox setup.

 

WARNING: 

Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.You may need 

to change the configuration of the firebox depending on which fireback option is being installed.  Carefully review the 
information below before proceeding with firebox setup. 

1.  Remove the glass frame and logs (see the installation manual for details). 

2.  Firebox baffle and exhaust restrictor must be removed to install firebacks (replace once firebacks in place). 

Firebox Ceiling

The baffle and exahaust restrictor have keyholes, allowing 

removal without removing the screws.

Firebox Baffle

 

 
 
 
 
 
 
 

Summary of Contents for 564 25K







Reviews: