background image

 
 

 

17 

 

Vegatouch Mira is a wireless control module that easily connects to any 
Android or iOS device to give total control to many electrical, electronic and 

mechanical systems in your coach.  Pair any device with the coach’s built

-in 

interface to monitor and control every component. 

 

Troubleshooting:

 

 

I CAN’T CONNECT TO MIRA WITH MY SMARTPHONE

/TABLET. 

Make sure that Bluetooth is enabled on your smartphone/tablet and follow 
the setup instructions on the next page.  Always make sure that you are 
using the most current version of the Mira app.  Update the app if 
necessary.   
 

WHEN I TRY TO CONNECT, THE SCREEN SAYS “SYNCING” AND NOTHING 

HAPPENS (OR SAYS OUT OF RANGE). 

Click on the settings page of your touchscreen and verify that your coach’s 
floorplan is selected.  If the floorplan is blank, Mira won’t be able to connect.

 

The network cable could also be faulty.  Inspect the cable at both ends and replace it if 
necessary.  If the cabling and setup seem to be correct, contact Firefly Integrations about 
possibly replacing the Mira module.   
 

Blinking NET LED: 

A blinking green NET LED on this module, please see page 26 of this manual. 
 

Password Reset:

 

R

eset the Mira’s password back to default (777777) by inserting a thin object, such as a 

toothpick, into the small hole on the front of the module and pressing the internal reset button 
for 5 seconds.  You can also reset the password from the Touchscreen by navigating to 
Settings/Mobile App and tapping Reset Pin to Default.    

NET LED 

 

Password  Reset 

 

Vegatouch Mira Modules 

Summary of Contents for VEGATOUCH LYRA Coach House V3




































Reviews: