Finn T30 HydroSeeder MO Parts And Operator'S Manual Download Page 4

 

 

Commercial Limited Warranty 

Effective    4/1/2011

 

OUR WARRANTY TO YOU:

 

Finn Corporation warrants to you, the original purchaser, for use (or rental to 
others for use) all new construction machinery, parts and attachments (except 
those referred to herein) that are manufactured by Finn to be free from 
defects in material and workmanship for a period noted above. 

 

 

Replacement parts provided under the terms of this warranty are warranted 
for the remainder of the warranty period applicable to the product to which 
parts are installed, as if parts were original components of the product. 

WHAT FINN WILL DO: 

Upon notification of Finn concerning a failure of material or workmanship in 
accordance with the above stated Warranty, Finn Corporation will: 

x

 

Verify claim falls within the valid warranty time frame. 

x

 

Verify the product and equipment has been 

registered

 with Finn in 

order to be eligible for warranty coverage. 

x

 

Upon affirmation of warranty period and registration, Finn will send to 
you a new or repaired replacement part(s), whichever Finn elects and a 

“Warranty Claim Information packet” containing instructions for 

processing the warranty claim. 

x

 

Evaluate the part when defective part is returned.  Note: Failure to 
return defective part within 

two weeks

 will result in an invoice being 

sent to the customer.  In addition, if damage to a part is determined not 
to be covered under the warranty, the customer will be billed. 

x

 

Reconcile costs with customer for parts and shipping, as determined by 
our inspection of failed parts, and confirmation of warranty coverage, 
per the terms of this warranty. 

x

 

Correction of nonconformities, in the manner provided above, shall 
constitute fulfillment of all liabilities of Finn Corporation. 

WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE: 

x

 

As the purchaser covered under the above limited warranty you must 

REGISTER

 the equipment with Finn FAILURE TO REGISTER 

WILL VOID THE WARRANTY.

 

x

 

Claim Number: Notify the warranty Dept. same day or next day of any 
intent to do war

ranty work and obtain a “Warranty Claim Number,” 

 

x

 

All warranty labor must be pre-approved by providing Finn with an 
estimate of labor costs.  Once approved, Finn will issue you a Work 
Authorization Number, prior to work being performed.(EXCEPTION: 
Unless the labor is per the Labor Allowance Schedule or less) 

x

 

The labor costs reimbursement will be based on the Labor Allowance 
Schedule established by Finn and where not applicable, on a reasonable 
number of hours as determined by Finn. 

x

 

Notify Finn Corporation of any failure of material or workmanship as 
described under this warranty. 

¾

 

Web notification: [email protected] 

¾

 

Phone 1-800-543-7166 extension 246 

x

 

Complete the required steps in the “Warranty Claim Information 
packet” (which Finn will send you

) and return the defective part(s) as 

directed in the packet to Finn Corporation. 

x

 

Should the failed part, be a hydraulic component, Finn may send you an 

“Oil Analysis Kit

,

 requesting that a sample of oil from the hydraulic 

system be taken, and mail it to a lab. Follow the instruction sheet, on 
how to use your Finn Oil Analysis Kit that comes with the Kit. Failure 
to comply when requested will void the warranty. 

WHAT THE WARRANTY DOES NOT COVER: 

1.

 

Normal wear parts and Allied Equipment or trade accessories not 
manufactured by it, such as but not limited to items such as various 
filters, fluids, brakes, clutch linings, belts, hoses, light bulbs, 
mechanical seal, over center clutches, tires, ignitions, starters, batteries, 
magnetos, carburetors, engines and labor, or like or unlike equipment or 
accessories. (Such being subject to the warranty, if any, provided by 
their respective manufacture). 

2.

 

Secondhand, used, altered, or rebuilt machines or parts. 

3.

 

Defects, malfunctions or failures resulting from accidents, abuse, 
misuse, improper servicing, or neglect of required operational 
guidelines and maintenance service, as outlined in the Finn 

Corporation’s Operators Manual(s).

 

   

4. The warranty shall be null and void to the extent any defect or failure of 
the products warranted arises out of or is caused by accessories or 
component parts not manufactured or supplied by Finn Corporation, 
whether same are supplied by purchaser, dealers, or any other party. 
5. This Warranty does 

NOT

 cover any costs associated with transporting 

the equipment for warranty service, such as mileage, fuel, or man hours; 
such is the responsibility of the equipment owner. 
6. Dealers & Customers are responsible to follow all guidelines related 
to Seasonal & Long Term Storage of Equipment, as advised in operation 
& equipment manuals. i.e. Finn, Engine, Clutch, Pump, Motor, etc. 
Equipment failures caused by neglect of these guidelines are not 
warrantable.

 

THIS IS THE ONLY EXPRESS WARRANTY ON OUR 
PRODUCTS:

 

We neither assume nor authorize anyone to assume for us any other 
express warranty.  The Distributor/Dealer has no authority to make any 
representation or promise on behalf of Finn Corporation or to modify the 
terms or limitations of this warranty in any way. 
THIS WARRANTY THEREFORE SHALL BE IN LIEU OF ALL 
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT 
NOT LIMITED TO, ANY IMPLIED WARRANTY OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 

LIMITATIONS ON OUR RESPONSIBILITY WITH 
RESPECT TO PRODUCTS PURCHASED: 

THE REMEDIES OF THE USER SET FORTH HEREIN ARE 
EXCLUSIVE, WITHOUT REGARD TO WHETHER ANY DEFECT 
WAS DISCOVERABLE OR LATENT AT THE TIME OF DELIVERY 
OF THE PRODUCT TO THE PURCHASER. 
ALL WARRANTY REPAIR MUST BE DONE BY A FINN 
AUTHORIZED SERVICE PROVIDER OR AUTHORIZED REPAIR 

SHOP OF FINN’S CHOICE.

 

TRANSPORTATION, HAULING, STORAGE, OR OTHER SIMILAR 

COSTS ARE NOT PART OF FINN’S OBLIGATION UNDER THE 

LIMITED WARRANTIES AND IS THE RESPONSIBILITY OF THE 
EQUIPMENT OWNER. 

THE ESSENTIAL PURPOSE

 of this exclusive remedy shall be to 

provide the original purchaser with repair or replacement of parts that 
prove to be defective within the period and under the conditions 
previously set forth. This exclusive remedy shall not have failed of its 
essential purpose (as that term is used in the Uniform Commercial Code) 
provided Finn remains willing to repair or replace defective parts within 
a commercially reasonable time after it obtains actual knowledge of the 
existence of a particular defect. 
 
IN NO EVENT shall Finn be liable for any special, consequential, 
incidental or indirect damages, including lost profits or lost 
commercial opportunities, with respect to the sale of the above 
warranted product or anything done in connection therewith, or for 
property damage sustained by a person claiming to be a third party 
beneficiary of a surviving warranty under the law of any jurisdiction. 

NOTICE: 

FINN CORPORATION URGES the use of only Finn corporation 
supplied parts and attachments to assure proper performance and safe 
operation of Finn corporation equipment. Insist on parts and 
attachments manufactured or supplied by Finn corporation when 
you purchase, repair or replace your Finn equipment and 
attachments. Because Finn corporation cannot assure that parts and 
attachments not manufactured or supplied by Finn meet Finn 
corporation's quality standards, specifications, or operating 
requirements, our warranty is not effective to the extent any failure of or 
defect in a Finn corporation product arises from or is caused by parts, 
attachments or components not originating with Finn corporation. Use of 
Finn corporation equipment with parts and attachments not 
manufactured or supplied by Finn could result in personal injury. 

 

Warranty period: 

Hydroseeders & Straw Blowers 2 years or 2000 hrs which ever comes 1

st

 

All other equipment 1 year or 1200 hrs which ever comes 1st

 

Summary of Contents for T30 HydroSeeder MO
























































Reviews: