08-EB2600-B0-EM, 05/17/2011
Main
Menu
Sub-
Menu
Range
Default
Description
0~3
-1999~9999
-1999~9999
DOT1
100.0
0
100.0
0.0
ON, OFF
OFF
SAVE,RSET
BACK
SAVE,RSET
BACK
Lo,MID,HI
SAVE
SAVE
LO
1/2"PT
HEX38
22
49.5
130
L= Customized
Length (mm)
f
38.1
2
2
2
2
2
Connect isolation cable with GND of power.
2
Connect tank with heater or cover of electric device to decrease EMI.
After installation of the Compact Capacitance LevelTransmitter on
the top of tank, please make sure the cover of the transmitter is
contacted with tank perfectly. Please avoid the grounding of panel
meter to touch the tank wall.
While the panel meter is not supplied with a power supply, please
prepare a 24V power supply for use. The wiring for panel meter is
showing in diagram 1.
The max cable length is depending on the max resistance.
Maximum resistance is not to exceed (Vs-15)
H
50
W
to
maintain the accuracy of measurement.
Make sure to separate the signal cable with other big power
cables (such as pump, conveyer and solenoid valve)while wiring.
Before turning on power, make sure all wirings are correct.
4
2
3
1
ENT
ENT
Power supply
Measuring range
Output current
Output
Output linear
range
Upper limit
Lower limit
Output latch
Linearity
Load resistance
Environment
temperature
Operation
temperature
Environment
humidity
Temperature
coefficient
LCD display
range
Protection degree
12~36Vdc
0~1000pF
4~20mA(
)
2 wire
3.8~21.5mA
22mA
3.5mA
3.5
、
22mA
A
1% F.S. or 1pF
(whichever is greater)
<(Vs-12)
H
50
W
Vs: Power Voltage (volt)
-40
B
C~80
B
C
According to the specification of probe
0~85% RH, non-condensing
<
A
0.02% F.S. per
B
C
-1999~9999
IP 65
-1999~9999
-1999~9999
12~36Vdc IN
REVERSIBLE
1
2
4
3
Lower present display range
Over present display range
Over measuring range (0~1000pF).
please add coating to decrease capacitance.
Output latch start up.
"OL"
"LACH" "1234"
"1"
"-1"
G:
Q:
B:
L:
V:
H:
R:
C:
M:
W:
O:
E:
Y:
T:
J:
A:
K:
U:
F:
P:
Z:
I:
S:
N:
D:
X:
60.0%
50.0%
40.0%
30.0%
20.0%
10.0%
0.0%
0
50
100
150
200
1000
(PF)
A
c
c
u
ra
c
y
(%
)
EB 2600 COMPACT CAPACITANCE
LEVEL TRANSMITTER
OPERATION MANUAL
Thank for buying FineTek's products.
Please read the user manual first before
using it. It is important to be familiar with
product's performance and function. Please
keep the user manual for operation refereuce.
WORKING PRINCIPLE
The level measurement of a medium in a tank is accomplished
by capacitance theory. The tank wall,
the sensing probe and the medium are all capacitors. A high
frequency since wave is applied between the probe and the
tank wall. The level change of the medium will cons equently
change the current of the applied since wave, forming a
proportional relationship between medium level and output.
OSC
CPU
Voltage
regulator
Signal
output
Capacitance level
transmitter
Tank
Sensing probe
16~30Vdc
DESCRIPTION OF PANEL
1. Button Protection, requiring to press ENT+UP
buttons for 2 seconds in order to get into main menu.
2. Reversible Polarity
3. Any two points for calibration
4. Retention for maximum and minimum values.
5. Three input buttons; user-friendly.
DIMENSION OF PRODUCT
WIRING DIAGRAM
ERROR MESSAGE
CODE
SPECIFICATION
DESCRIPTION OF PANEL
LCD display
UP button
1
2
Shift button
Enter button
4
3
Colors of wiring
1: Brown
2: Green
3: Blue
4: Black
PROGRAM SETTING FLOW CHART
WIRING AND CAUTION
Signal GND
[ Description of Wiring ]
2
3
4
5
6
7
8
1
+24V
EXC 24V
A Input
The Signal GND of panel meter should not be connected
with tank wall or the cover of the EB Transmitter, otherwise
the measurement will be incorrect.
(Diagram 1)
Panel Meter
Panel Meter
Power Supply
Signal GND
2
3
4
5
6
7
8
1
EXC 24V
A Input
+24V
Warning
DESCRIPTION OF PARAMETERS
PF & accuracy chart
Decimal point setting
20mA corresponding
display value
4mA corresponding
display value
Corresponding calibration value for
high point (Hipt). See remark 1
Corresponding Calibration Value for
low point (Lopt). See remark 1
Memory for max & mini value
during operation.SAVE:Save value
into Eeprom
REST:Clean present value and
memoryBACK:Go back to sub-menu
Output latch enable or disable.
See remark 2.
Software Filter
Remark 1: Please refer to calibration procedure for HIPT & LOPT setting.
Remark
If you select ON, the output will be latched at 3.5mA/22mA
when it reached to 3.5mA/22mA.
2:
Display Value
2sec
Capacity Value
High point Capacity Value
Low point Capacity Value
0~9999
0~9999
5056
0~9999
54
