Fimer VSN300 Quick Installation Manual Download Page 7

7

9.  Identification label

This label is necessary to remember all the identification data of VSN300 WIFI LOGGER CARD and it should be applied in the dedicated area shown 

below. 

 

FIMER
VSN300 WIFI LOGGER CARD

SN: YYWWSSSSSS

MAC:  XX:XX:XX:XX:XX:XX

PRODUCT KEY:  XXXX - XXXX - XXXX - XXXX

APPLY HERE THE

 IDENTIFICATION LABEL

 ATTENTION – 

A

Save these instructions! The information on the above label will be used by Technical Service in case of problems.

10.  Characteristics and technical data

VSN300 WIFI LOGGER CARD

Communication

Inverter interface

Hyperlink (CAN@1 Mbps + RS485@115 kBaud) / Legacy (Serial link TTL @ 19.2 KBaud)

User interface

Wi-Fi Certified™ IEEE 802.11 b/g/n (2,4 GHz)

Communication Protocols

LAN/WAN protocols

HTTPS, DHCP, NTP, SSL, SSH, XML, Modbus TCP (Sunspec)

Monitoring

Web user interface (WUI)

Integrated

Local monitoring

Wirelessly allowed via any Wi-Fi ® device connecting the integrated WUI or running Plant Viewer for 

Mobile

Remote monitoring

Plant Portfolio Manager ® / Plant Viewer™ / Plant Viewer for mobile

Data Logging Specifications

Data sampling rate

High frequency data sampling (less than 1 minute average)

Local data storage

Log data for 30 days based on 15-minute intervals

Upgradeability

Remotely via Aurora Vision® Plant Management Platform / locally via integrated Web User Interface 

(1)

Advanced functionalities

Remote O&M operations

Inverter’s parameter setting 

(2)

 / inverter’s firmware upgrade 

(2)

Smart grid functionalities

Grid control power-management enabled 

(2)

Power Supply

DC power consumption

~ 2W

Environmental Parameters

Ambient temperature range

[-20; +85]°C

Environmental protection

IP 20

Relative humidity

<85% Non-condensing

Mechanical Parameters (per unit)

Dimensions (H x W x D)

 97mm x 46mm x 16mm (3.81’ x 1.81’ x 0.63’)

Weight

0.06 lbs (26g)

Mounting system

Inverter’s expansion slot

Compliance

Marking

CE / RCM / Wi-Fi Certified™

Emissions

47 CFR FCC Part 15 Subpart C, EN 55022 Conducted and radiated emission

Immunity

EN55024

1. Available from FW version FW 1.8.x

2. Check for availability

Remark. Features not specifically listed in the present datasheet are not included in the product

Summary of Contents for VSN300









Reviews: