2
1. Product Identification - Labels and Symbols
“Before installing the VSN300 Wifi Logger Card it is strongly recommended to previously read both the present Quick Installation Guide (QIG) and the
product manual (available on FIMER official web site www.fimer.com).
The present QIG refers to VSN300 Wifi Logger Card in FW version 1.8.x on.
The VSN300 WIFI LOGGER CARD printed circuit board will be marked with the following information, identifying the product:
-Manufacturer Mark/Trade Mark
-CE (European Union) Marking
-RCM (Australia) Marking
-FCC ID
The FCC ID is FCC ID: X6W-3N16E when the VSN300 WIFI LOGGER CARD is assembled with a Wi-Fi radio module supplied by Epcos
The FCC ID is FCC ID: X6W-3N16M when the VSN300 WIFI LOGGER CARD is assembled with a Wi-Fi radio module supplied by Murata
A dedicated label including the FCC ID must be placed in a visible position on the exterior of the Inverter host equipment
Contains FCC ID: X6W-3N16E
Contains FCC ID: X6W-3N16M
FCC (Federal Communications Commission) WARNING
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in any particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
3. RF Exposure. This device complies with Part 2.1091 of the FCC Rules for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the antenna and the user.
Refer to the specific section describing procedures how to integrate and use this device into the host fixed mount inverter.
Changes or modifications made to this equipment not expressly approved by the Manufacturer may void the FCC authorization to operate this equipment.
The identification label contained on the VSN300 WIFI LOGGER CARD box has information regarding the device and manufacturer.
FIMER
VSN300 WIFI LOGGER CARD
SN: YYWWSSSSSS
MAC: XX:XX:XX:XX:XX:XX
PRODUCT KEY: XXXX - XXXX - XXXX - XXXX
- Manufacturer name
- Model name
- Serial Number composed of:
YY = Year of production
WW = Week of production
SSSSSS = progressive number
- VSN300 WIFI LOGGER CARD Mac address
- Product Key composed of 16 characters used to activate the VSN300 WIFI LOGGER CARD
In some cases on the equipment, dangerous or hazardous zones are indicated with signs, labels, symbols or icons.
In the manual and/or in some cases on the equipment, the danger or hazard zones are indicated with signs, labels, symbols or icons.
Always refer to instruction
manual
Hot surfaces
General warning - Important safety
information
,3;;
Protection rating of
equipment
Dangerous voltage
Temperature range
Obligation to use protective clothing
and/or personal protective equipment
;;
The discharge time of the
stored energy
2. Operating diagram
The VSN300 WIFI LOGGER CARD allows for connection of the inverter to a local LAN Wi-Fi network via a wireless connection.
The VSN300 WIFI LOGGER CARD features an integrated web server that enables establishment of a direct connection to a PC,smartphone or tablet,
allowing for board configurations and local monitoring of the inverter.
When the inverter is connected to the WLAN network with Internet access, the VSN300 WIFI LOGGER CARD allows for transfer of data to the Aurora
Vision® Plant Management Platform for remote monitoring purposes over an Internet browser or Mobile App (Plant Viewer for Mobile)
APPLICATION WITH VSN300 WIFI LOGGER CARD
WI-FI router
INTERNET
POWER
ALARM
GFI
ESC
UP
DOW
N EN
TER
TRIO
TRIO
POWER AL
ARM
GFI
ESC
UP
DOWN
ENTER
Aurora Vision
Plant Management Platform™
®
Aurora Vision
Plant Viewer for Mobile
J1
U8
U3
U11
U7
J2
1
2
23
24
VSN300
WIFI LOGGER CARD
ATTENTION –
A
In order to assure the correct operation of the card do not install other monitoring devices in addition to the VSN300 WIFI LOGGER CARD.
