background image

Page 4 

 

1.  Start by sliding Item 4, 3, 2 onto the boom tube (Item 1) as shown, leaving 

about 1/2” to 3/4” between the end of the boom tube and Item 2. Make 

sure the “Long” portion of Item 3 is facing the nozzle end. 

2.  Slide the (complete) end nozzle assembly onto the stainless steel boom 

tube, with a somewhat “twisting” motion, so that the end face of the boom 

tube “butts” up against the surface face inside the nozzle body. 

3.  Now push the “compression olive” (Item 3) against O-ring 

(Item 2) and slide (both) into the nozzle body opening firmly. 

4.  Firmly tighten flynut (Item 4) onto threads of nozzle body. 

5.  Repeat for other side. 

 

NOTE: If water is shooting back on the boom tube, item 2 is not 

in the correct placement. 

End Nozzle Assembly Procedure 

For Boomless “Wet”Boom 

Your boom will come with the (2) end nozzle assemblies 

NOT affixed to your boom tube. Follow the instructions 

below to attach these properly to the boom tube, as 

shown. 

Assembled 
End Nozzle 

15° 

End Nozzle Information  (5275122) 

** Each “click” of the ratcheting motion is approx. 15° ** 

This nozzle mounting stem 

Has a ratcheting motion. 

For proper/optimal spray coverage, 

The nozzle must be at a 15° angle 

 

The 15° angle shown will prevent the outer 

Nozzles from overlapping with the center nozzle. 

“On/Off” Valve Positions 

Note: The check valve & diaphragm can fall out during transport, if the 

knob is not turned to the “ON” or “OFF” position. 

On/Off Valve Knob 

Eliminate line pressure, then pull out 

to check diaphragm condition. 

Valve “Open” 

Service Position 

Valve “Closed” 

Step 5 

After  your  boom  is  attached,  locate  the  48”  hose  and  the 

(2) hose clamps from the parts bag. 

 

Place the hose clamps over each end of the hose loosely. 

Slip the ends of the hose over the hose barbs on both the 

manifold and on the center nozzle. Use a twisting motion, 

if necessary, to get the hose fully onto each barb. Bring the 

hose clamps to the connection point and tighten securely. 

 

NOTE: 

Make sure this boom feeder hose does not end up on the 

‘outside’  of  the  spray  wand  hose,  otherwise  unwrapping 

the spray wand hose from around the tank may be difficult. 

Step 4 

Item 2 is shipped inside of 

the end nozzle assembly. 

Remove & place on tube.

 

Summary of Contents for ATVBK-3025-QR









Reviews: