Fimap MAXIMA BASE BT 2017, Use And Maintenance Manual

Page: 13 / 28

MACHINE PREPARATION
HANDLING THE PACKAGED MACHINE
The machine is contained in specific packaging, and since the
packaging elements (plastic bags, staples, etc.) are a potential source
of danger, they should not be left within the reach of children, disabled
persons, etc.
The machine's overall weight including packaging is 000 Kg.
The overall dimensions of the package are: A=765 mm B=1460 mm
C=1270 mm.
ATTENTION : it is recommended that all the packaging
components be kept for any future machine transportation.
ATTENTION : move the packaged product with handling
equipment that complies with legal requirements regarding size
and mass of the packaging.
HOW TO UNPACK THE MACHINE
The machine is shipped in specific packaging. To remove it, proceed as follows:
1. Place the lower part of the outer packaging in contact with the floor.
NOTE : use the pictograms printed on the box as a reference.
2. Remove the outer package.
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Make sure the machine is switched off. If it isn't, turn the main switch (1) to “0” by rotating the key
a quarter turn in the direction shown by the arrow (
Fig.1
). Remove the key from the instrument
panel.
4. Grip the handle (2) on the right-hand side of the recovery tank (
Fig.2
) and turn the tank as far as
it will go, until it reaches the maintenance position.
5. Connect the pad battery connector (3) to the main system connector (4) (
Fig.3
).
CAUTION : this process must be carried out by qualified personnel.
6. Grip the handle (2) on the right-hand side of the recovery tank and turn the tank until it reaches
the work position.
7. The machine is fixed to the pallet by means of wedges (5) that block the wheels and brush head
( Fig.4 ). Remove the wedges.
8. Insert the ignition key and switch on the machine. Turn the main switch (1) to “I” by rotating the
key a quarter turn in the direction of the arrow ( Fig.5 ).
9. Raise the brush head body and fully depress the "BRUSH HEAD CONTROL" pedal (6) at the
rear of the machine ( Fig.6 ).
NB : to lock the brush head in the raised position, depress the pedal (6) fully and then move it
towards the right-hand side of the machine ( Fig.6 ).
10. Raise the squeegee body and turn the squeegee control lever (7) in the direction of the arrow
( Fig.7 ). The lever is located on the back of the machine.
11. Press the “REVERSE ACTIVATION - DEACTIVATION” button (8) on the control handlebars ( Fig.8 ).
NB : as soon as the button (8) on the control panel is pressed, the green LED (“REVERSE
ACTIVE”) will switch off ( Fig.8 ).
12. Activate the dead man's lever (9) underneath the control handlebars ( Fig.9 ) to start moving the
machine in reverse.
13. Use a ramp to bring the machine down from the pallet.
CAUTION : do not fit the brush and the rear squeegee body before unloading the machine, and
avoid any violent jolts to the brush head and squeegee support.
NB : the ramp gradient must not be such as to cause damage to the machine as it comes
down.
14. Switch off the machine by turning the main switch (1) to "0", making a quarter turn of the key in
the direction of the arrow ( Fig.1 ). Remove the key from the instrument panel.
15. Grip the handle (2) on the right-hand side of the recovery tank ( Fig.2 ) and turn the tank as far as
it will go, until it reaches the maintenance position.
16. Disconnect the pad battery connector (3) from the main system connector (4) ( Fig.3 ).
ATTENTION : this process must be carried out by qualified personnel.
17. Grip the handle (2) on the right-hand side of the recovery tank and turn the tank until it reaches
the work position.
HOW TO MOVE THE MACHINE
To transport the machine safely, proceed as follows:
DANGER : before starting any task, make sure the current regulations concerning the safe
transport of dangerous substances are scrupulously observed.
1. Check the solution tank and recovery tank are empty. If they aren't, empty them (see
“ EMPTYING THE SOLUTION TANK ” and “ EMPTYING THE RECOVERY TANK ”).
2. Insert the key (1) in the main switch on the control panel. Set the main switch to “I” by turning the
key (1) to the right ( Fig.1 ).
3. Raise the brush head body and fully depress the "BRUSH HEAD CONTROL" pedal (2) at the
rear of the machine ( Fig.2 ).
NB : to lock the brush head in the raised position, depress the pedal (2) fully and then move it
towards the right-hand side of the machine ( Fig.2 ).
4. Raise the squeegee body and turn the squeegee control lever (3) in the direction of the arrow
( Fig.3 ). The lever is located on the back of the machine.
5. When you push the dead man's lever (4) ( Fig.4 ), the machine will begin to move.
6. Use a ramp to move the machine up onto the transport vehicle.
CAUTION : during this operation, check there are no people or objects near the machine.
NB : the ramp gradient must not be such as to cause damage to the machine as it goes up.
7. Once the machine is on the means of transport, set the main switch to “0” by turning the key (1)
to the left ( Fig. 5 ). Remove the key from the main switch.
8. Grip the handle (5) and raise the recovery tank to its maintenance position ( Fig.6 ).
9. Disconnect the battery connector (6) from the main system connector (7) of the machine ( Fig.7 ).
10. Grip the handle (5) and lower the recovery tank to its working position.
WARNING : secure the device according to the directives in force in the country of use, so that it
cannot slide or tip over.
13
2
8
1
7
3
9
1
2
7
8 9
3
4
4
4
5
1
6
5
7
6
7
5 4 6
1
5
6
2 1 3
1
2
3