manualshive.com logo in svg

Fimap IMx, Workshop Manual, Page: 76 / 94

Share
Download
Fimap IMx Workshop Manual Download Page 76

7-76

•

Remove and clean (replace if neces-
sary) the filter.

7.4.4-22 Recovery

Tank

Lid

7.4.4-23 Filter Cup

7.4.4-24 Ball Filter

7.4.5

Recovery Tank

Checks

The recovery tank has to be clean and
has not to have cracks or, in general, any
kind of damage. The Lid housing has to
be even and flat to allow the gasket to ad-
here perfectly to the tank to avoid any air
infiltration. The hose fittings have to be
in optimum condition in order to avoid
any dirty water leakage or any pressure
drop during the job.

7.4.6

Vacuum Motor

Checks

The vacuum motor with the inlet com-
pletely open has to absorb between 13
and 18A. The motor carbon brushes
have to be in good conditions and their
length has to be no lower than 6-8mm.
The motor contacts have to be clean,
they have not to be oxidized or have any
kind of damage. The motor wires insula-
tion has to be flexible and intact to avoid

7.4.5-25 Vacuum Cover

7.4.5-26 Recovery Tank

7.4.5-27 Vacuum Hose

7.4.5-28 Vacuum Hose

7.4.5-29 Drain Hose

any possible short circuit. The magnetic
circuit of the motor has to be in good
conditions and clean.

Maintenance

•

Put the machine in safe conditions.

•

Disassemble the motor from the ma-
chine

(see section

4.3.10

at page

29

)

.

•

Remove the cooler fan plastic cover
from the motor

(see fig.

7.4.6-30

)

.

7.4.6-30 Plastic cover re-
moval

Summary of Contents for IMx































































































Reviews:

No comments