Fimap FM1500 S Use And Maintenance Manual Download Page 16

 

 

 

16 

EC DECLARATION OF COMPLIANCE 

 

The undersigned company: 

FIMAP S.p.A. 

Via Invalidi del Lavoro no.1 

37050 Santa Maria di Zevio (VR) 

declares under its sole responsibility that the products 

 

SINGLE BRUSH MACHINES mod. FM1500 S – FM1500 V 

 

comply with the requirements of the following Directives: 
 

 

2006/42/EC: Machinery Directive 

 

2006/95/EC: Low Voltage Directive 

 

2004/108/EC: Electromagnetic Compatibility Directive 

 

They also comply with the following standards: 

 

EN 60335-1: Household and similar electrical appliances - Safety. Part 1: Generic norms 

 

EN 60335-2-67: Household and similar electrical appliances. Part 2: Specific norms for automatic machines for floor treatment for 
commercial and industrial use 

 

EN 12100-1: Machine safety - Fundamental concepts, fundamental principles of design - Part 1: Basic terminology and methodology 

 

EN 12100-2: Machine safety - Fundamental concepts, fundamental principles of design - Part 2:  Technical principles 

 

EN 55014-1: Electromagnetic compatibility - Regulations for household appliances, electrical devices and similar equipment. Part 1: 
Emission - Regulations for product family. 

 

EN 55014-2: Electromagnetic compatibility - Regulations for household appliances, electrical devices and similar equipment. Part 2: 
Immunity - Regulations for product family.  

 

EN 61000-3-2: Electromagnetic compatibility (EMC) - Part 3-2: Limits – Limits for harmonic current emissions (Equipment with input 
current 

 16 A per phase).  

 

EN 61000-3-3: Electromagnetic compatibility (EMC) - Part 3-3: Limits – Restriction of voltage variations and flicker in low voltage power 
supply systems for devices with a rated current 

 16 A. 

 

EN 62233: Household and similar electrical appliances - Electromagnetic fields Methods for evaluation and measurement 

 

The person authorised to compile the technical file: 

 
Sig. Giancarlo Ruffo 

Via Maestri del Lavoro, 13 

37059 Santa Maria di Zevio (VR) - ITALY

 

 

 
Santa Maria di Zevio, 21/10/2010 

 

 

 

 

 

 

 

 

 

 

        FIMAP S.p.A. 

 Legal  representative 

Giancarlo Ruffo 

 
 

 

 

 

 

 

 

 
 

 

 

FIMAP spa  

Via Invalidi del Lavoro, 1 - 37050 S.Maria di Zevio (Verona) Italy 

Tel. +39 045 6060411 r.a. - Fax +39 045 6060417 - E-mail:[email protected]

www.fimap.com

 

 

Summary of Contents for FM1500 S

















Reviews: