manualshive.com logo in svg

Fike TWINFLEXpro, Manual

Share
Download
Fike TWINFLEXpro Manual Download Page 17

TWINFLEX

®

pro Repeater Panel Engineering and Commissioning Manual 

 
 

17 

 

General Operation of Repeater Panel 

Control Panel Front  

 
 

 

 

 

 

 

 

LED Indication 

 

The operation of the LED indication on the front of the repeater panel is described below. The LED 
indication on the repeater panel can also be confirmed by checking the message displayed in the 
repeater information screen or by accessing the relevant event log from the repeater menu. 

 

Description 
 

Colour 

State 

Reason 

FIRE 

Red 

Continuous 

The control panel is in the fire state.  Display  will 
show the zone of origin. 
 

FAULT 
 

Yellow 

Continuous 

The control panel is in the fault state.  Display  will 
show the origin. 
 

DISABLED 
 

Yellow 

Continuous 

This indicates that a disablement action is in place. 
 

TEST 
 

Yellow 

Continuous 

This indicates that a test routine is in place.  

POWER 

Green 

Continuous 
 
 

This indicates that power is being supplied to the 
panel. 

General Indication LEDs 

Repeater Information 
Screen 

Fire Alarm Controls / 
Controls Enabled Keyswitch 

System Controls 

Summary of Contents for TWINFLEXpro



























Reviews:

No comments

Brands by name

Popular brands

Load more brands