manualshive.com logo in svg

Fike TWINFLEXpro, Manual

Share
Download
Fike TWINFLEXpro Manual Download Page 16

TWINFLEX

®

pro Repeater Panel Engineering and Commissioning Manual

 

 

16 
 

Commissioning 

 

•

 

Check that the repeater has been correctly and securely mounted to the wall. 

 

•

 

Check that the date and time are correct and match the date and time on the main control panel 
which it is connected to. Check that the time increments with the main control panel which it is 
connected. 

 

•

 

Carry out all 5 tests below: 

  

Option 3. Test RDU 

1.  Test LEDs 
2.  Test Keypad 
3.  Test Buzzer 
4.  Test LCD 
5.  Test Backlight 

 

•

 

Verify that fire alarms and faults are displayed correctly and match the main control panel which it is 
connected to. 
 

•

 

Training for the users of the system and responsible persons See End User Training below. 

 

 

Fault finding 

If the date and time do not update and are not in synchronisation with the main panel check the wiring 
at the repeater and the main panel is correct. 
 
Check the setting in the main panel and repeater. 
 
The panel will report RDU missing if there is no communications between the main control panel and 
the repeater or if the repeater address number does not match the RDU enabled number in Option 1 
PB RDU Supervise in the main control panel. 
 
If for example RDU 1 is set in the main control panel Option 1, PB RDU Supervise and the repeater that 
is connected to the peripheral bus is set to a different address i.e. number 2, the panel will report “RDU 
1 Missing”. 

 

 

 

Summary of Contents for TWINFLEXpro



























Reviews:

No comments

Brands by name

Popular brands

Load more brands