Fike ECS Series Installation & Operation Manual Download | Manualshive

Page: 34 / 66

background image

34

ECS Series Manual —

P/N LS10262-001FK-E:A 3/3/2021

Device Installation

Installing the FIK-INT50W

4.4 Installing the FIK-INT50W

This section provides information on how to install the FIK-INT50W for use with the ECS Series products. The FIK-INT50W Internal
Amplifier can fit inside the FCP-300ECS cabinet. It can also be adapted to fit into the FCP-2100ECS cabinet with the FIK-AMPMT mount-
ing kit (sold separately). It is used to amplify the audio message for distribution throughout the facility for the Emergency Communication
System.

4.4.1 Board Layout & Mounting

Figure 4.22 Front View of FIK-INT50W

Mounting the FIK-INT50W

1.

Remove AC power and disconnect the backup batteries from the main control panel.

2.

To mount the FIK-INT50W inside the FACP cabinet under the main board, align the board with the mounting holes. Secure the board to
the enclosure with the supplied screws. See Figure 4.23.

Figure 4.23 FIK-INT50W in FACP Cabinet

3.

When mounting the FIK-INT50W in the ECS cabinet that contains an FIK-NVCM, it is necessary to mount the FIK-INT50W on the
right side of the control board. To do this, you will need the FIK-AMPMT mounting kit (ordered separately).

SBUS

VBUS

DIP Switch

Power

IN1 / OUT1

«
...
32
33
34
35
36
...
»

Summary of Contents for ECS Series



































































Reviews:

No comments

Related manuals for ECS Series

Brand: Thermo Scientific Pages: 68

Brand: Grundfos Pages: 23

Brand: Danfoss Pages: 8

Brand: Jacuzzi Pages: 28

Brand: N-Com Pages: 12

Brand: Regintech Pages: 82

Brand: Wavemaster Pages: 32

Brand: Xiron Pages: 29

Brand: Pioneer Pages: 8

Brand: Pioneer Pages: 64

Brand: Pioneer Pages: 64

Brand: BMPRO Pages: 32

Brand: RCA Pages: 18

Brand: Kurt Pages: 20

Brand: JVC Pages: 2

Brand: JVC Pages: 1

Brand: JVC Pages: 25

UXG50 - CD Microsystem With USB Audio

Brand: JVC Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands